6730C010000 FAN AIR VALVE
一、名称FAN AIR VALVE风扇活门二、件号6730C010000,6730C010000 AMDT A,6730C010000 AMDT B,6730C010000 AMDT C三、章节号36-11-57四、适用机型A319, A320五、系统36-PNEUMATIC气动六、安装位...
737NG-30防冰防雨【系统原理】
737NG-TECHNICAL TRAINING MANUAL技术培训手册ATA 30 防冰防雨目录1．介绍2．一般描述3．机翼防冰1）介绍2）部件位置3）防冰面板4）防冰活门5）地面过热电门6）伸缩管7）操纵台机翼防冰电门8）...
3505920 TGA/MSOV/ISOLATOR ASSEMBLY
一、名称TGA/MSOV/ISOLATOR ASSEMBLY涡轮齿轮箱/调节关断活门/隔离器组件二、件号3505920-5~-9三、章节号29-11-25四、适用机型B777-200五、系统29 HYDRAULIC POWER液压六、安装位置the left win...
3399102 PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLER
一、名称PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLERPRSOVC压力调节和关断活门控制器 PRSOVC二、件号3399102-2~-4,-6~-12,-20,-30,-40三、章节号36-13-59四、适用机型B777-200五、系统36-...
6730F010000 FAN AIR VALVE
一、名称FAN AIR VALVE风扇活门二、件号6730F010000,6730F010000 Amdt A三、章节号36-11-11四、适用机型A319, A320五、系统36-PNEUMATIC气动六、安装位置发动机吊架七、部件原理A. General Desc...
3399100 HIGH PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLER/HPFAC – high pressure fan air controller
一、名称HIGH PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLERHPFAC - high pressure fan air controller高压调节器及关断活门控制器HPFAC - 高压风扇控制器(在七、部件原理和九、在飞机系统...
3290476 SURGE CONTROL VALVE
一、名称SURGE CONTROL VALVE防喘控制活门二、件号3290476-3~-5三、章节号49-50-95四、适用机型A330/A340五、系统49 AIRBORNE AUXILIARY POWER机载辅助动力装置(APU)六、安装位置APU， 315区域...
SECTION VI – PACKAGING – 包装（完）
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
SECTION IV – ASSEMBLY 8-Marman卡箍（联轴器）安装
8.Marman Clamp (Coupling) InstallationMarman卡箍（联轴器）安装(1) Position clamp over mating component flanges as described in applicable manual.参照适用手册说明，将卡箍定位于配合...
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
SECTION IV – ASSEMBLY 4-压装过盈配合零件
4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...
SECTION IV – ASSEMBLY 3-锥形密封件
3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
