SECTION IV – REPAIR 4. 修理铝制零件-E.Method No. 404E:轻微腐蚀修复
4. Repairing Aluminum Parts 修理铝制零件E.Method No. 404E: Minor Corrosion RepairMethod No. 404E:轻微腐蚀修复Remove minor corrosion from aluminum-alloy parts as follows:按如下步骤...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-H.Method No. 407H：松动、磨损或损坏的 Rosan螺柱和钢丝螺套的更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板H.Method No. 407H: Loose, Worn, or Damaged Rosan Stud and Insert ReplacementMethod No....
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-L.Method No. 403L: 修复因底漆和面漆损坏而暴露裸露镁的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用L.Method No. 403L: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
SOPM20-50-16压接钢索的组装
压接钢索的组装ASSEMBLY OF SWAGED CABLES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5002. Access to the Boeing Process Specification...
SECTION IV – REPAIR 5.清除钢制零件上的损伤-C.Method No. 405C: 使用玻璃珠喷丸修复密封直径（唇形密封面）
5.Removing Damage from Steel Parts清除钢制零件上的损伤C.Method No. 405C: Seal Diameter (Lip Seal Surface) Repair Using Glass Bead PeeningMethod No. 405C: 使用玻璃珠喷丸修复密封直径...
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
3399102 PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLER
一、名称PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLERPRSOVC压力调节和关断活门控制器 PRSOVC二、件号3399102-2~-4,-6~-12,-20,-30,-40三、章节号36-13-59四、适用机型B777-200五、系统36-...
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
SOPM20-30-94应用防雨侵蚀涂料前进行最终清洗的溶剂（94系列）
应用防雨侵蚀涂料前进行最终清洗的溶剂（94系列）SOLVENTS FOR FINAL CLEANING BEFORE APPLICATION OF RAIN EROSION RESISTANT COATINGS (SERIES 94) 1. GENERAL 通用 A. Thissubject contai...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-D.Method No.403D：金属喷涂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用D.Method No. 403D: Metal Spray RepairMethod No.403D：金属喷涂修复NOTE: Electric Arc Spray and...
SECTION IV – REPAIR 修理（三）-J.Method No. 403J: Selective Electroplating
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
Honeywell-STORAGE存储
存储（含运输）STORAGE (INCLUDING TRANSPORTATION) 1. Planning Data 计划数据 A. Reason for the Job 工作原因 (1) Use these procedures to prepare the modulating shutoff valve for stora...
SECTION III – INSPECTION 1. Standard Inspection Practices -I.弧形联轴器检查
I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-I.Method No. 407I:松动、磨损或损坏的螺母板（铆接式）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板I.Method No. 407I: Loose, Worn or Damaged Nutplate (Riveted) ReplacementMethod No. 407...
SECTION III – INSPECTION 1. Standard Inspection Practices -F. 齿轮和花键检查
F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...
6730F010000 FAN AIR VALVE
一、名称FAN AIR VALVE风扇活门二、件号6730F010000,6730F010000 Amdt A三、章节号36-11-11四、适用机型A319, A320五、系统36-PNEUMATIC气动六、安装位置发动机吊架七、部件原理A. General Desc...
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
