张群
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-C.Method No.403C：薄而致密的镀铬零件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用C.Method No. 403C: Thin Dense Chrome Plated Parts RepairMethod No.403C：薄而致密的镀铬零件修...
SECTION IV – REPAIR 4. 修理铝制零件-E.Method No. 404E:轻微腐蚀修复
4. Repairing Aluminum Parts 修理铝制零件E.Method No. 404E: Minor Corrosion RepairMethod No. 404E:轻微腐蚀修复Remove minor corrosion from aluminum-alloy parts as follows:按如下步骤...
第七章 插头（座）的装配及工具的使用
详解航空插头（座）装配标准施工工艺，涵盖手动/气动/液压夹接工具操作、插钉/孔夹接与送退方法（前退/后退）、插头尾部屏蔽地线四种制作方式、插头磅力矩操作及保险丝制作，适用于SWPM手册施工...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-N.Method No. 403N: 铝的化学膜修补
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用N.Method No. 403N: Chemical Film Touch-Up of AluminumMethod No. 403N: 铝的化学膜修补(1) Remov...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-D.Method No.403D：金属喷涂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用D.Method No. 403D: Metal Spray RepairMethod No.403D：金属喷涂修复NOTE: Electric Arc Spray and...
SECTION III – INSPECTION 1. Standard Inspection Practices -O.设备和材料
O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...
SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
INSPECTION 检查 三 Inspection Procedures
一份全面的航空部件无损检测（NDT）程序手册，详述了14项检测方法。涵盖射线检测（ASTM E1742）、超声波检测（MIL-STD-2154）、敲击测试、接触式蓝染、表面淬火层检测（MIL-STD-867）、硝酸盐蚀...
737NG-ATA 51 结构【系统原理】
目录1．一般描述2．复合材料1．一般描述 概述 这里有飞机的大体尺寸。 2．复合材料概述部分飞机结构和部件是复合材料制成的。这些材料有以下优点：高强度；防腐；增加疲劳寿命；减轻重量。
SECTION IV – REPAIR 8-齿轮齿修复-A.Method No. 408A:齿轮齿渐开线表面轻微损伤修复
8. Repairing Gear Teeth齿轮齿修复A.Method No. 408A: Minor Gear Teeth Involute Surface Damage RepairMethod No. 408A:齿轮齿渐开线表面轻微损伤修复Repair minor surface damage on gear t...
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-E.Method No. 407E: 松动、磨损或损坏的衬套（铝或镁部件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407E: Loose, Worn, or Damaged Bushings (Aluminum or Magnesium Parts) Repl...
SECTION IV – REPAIR 5.清除钢制零件上的损伤-C.Method No. 405C: 使用玻璃珠喷丸修复密封直径（唇形密封面）
5.Removing Damage from Steel Parts清除钢制零件上的损伤C.Method No. 405C: Seal Diameter (Lip Seal Surface) Repair Using Glass Bead PeeningMethod No. 405C: 使用玻璃珠喷丸修复密封直径...
SECTION IV – REPAIR 4. 修理铝制零件-D.Method No. 404D:燃油和滑油泵铝制壳体表面修复
4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-E.Method No. 403E：干膜润滑剂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用E.Method No. 403E: Dry-film Lubricant RepairMethod No. 403E：干膜润滑剂修复Dry-film lubricant...
第三章 标准线路施工手册（SWPM）介绍
本文介绍标准线路施工手册（SWPM）的基本功能与使用方法，包括通过线号或系统章节查找导线、导线束的方法，以及线型代码（WTC）的查询步骤，帮助维修人员高效查阅手册。
