O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...

O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...

M.Thermocouple Simulators for Calibration and Checkout of Electronic Equipment 用于电子设备校准和检查的热电偶模拟器 (1) For test purposes in simulating a thermocouple, a common and...

N.Composite Material Components 复合材料部件 (1) Check per Table 308. 按照表308进行检查。

N.Composite Material Components复合材料部件(1) Check per Table 308.按照表308进行检查。

M.Thermocouple Simulators for Calibration and Checkout of Electronic Equipment 用于电子设备校准和检查的热电偶模拟器(1) For test purposes in simulating a thermocouple, a common and ...

3. Standard Cleaning Methods 标准清洁方法 CAUTION: SPECIFIED CLEANING METHODS OUTLINED MUST BE FOLLOWED. THE VARIOUS SOLUTIONS AND MATERIALS SPECIFIED IN THE CLEANING METHODS CAN B...

SECTION III – INSPECTION第三章 – 检查 TABLE OF CONTENTS 目录 SECTION 章节 1. Standard Inspection Practices 标准检查施工 A. General 通用 B. General Inspection Procedures 通用检查...

INTRODUCTION介绍 1. General 通用 Information provided in this manual pertains to overhaul and repair processing for parts manufactured by Honeywell Inc., Phoenix, Arizona. 本手册提...

SECTION I – DISASSEMBLY分解 TABLE OF CONTENTS 目录 SECTION 章节 1. Standard Disassembly Practices 标准分解操作 A. General 通用 B. Identification of Matched Parts and Sets 识别配合...

2. Preparation of Cleaning Solutions 清洁溶液的配制 WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARAT...

E. Bearing Inspection 轴承检查 (1) Separable Bearings: 可分解的轴承。 Table 301. Separable Bearing Defect Definitions 表301 可分解轴承缺陷的定义 Term 项目 Definition (Description o...

F. Gear and Spline Inspection 齿轮和花键检查 (1) Check gear and spline teeth as follows: 检查齿轮和花键齿，如下所示： (a) Perform visual check using a strong light and a minimum of...

G. Visual Inspection 目视检查 (1) General Information 通用信息 (a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause...

H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...

I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...

K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...

L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...

TABLE OF CONTENTS 目录 SECTION 章节 1. Standard Cleaning Practices 标准清洁规范 A. General 通用 2. Preparation of Cleaning Solutions 清洁溶液的配制 A. Method No. 202A: Alkaline Cle...

4. Alternate Cleaners 替代清洁剂 A. General 通用 (1) Alternate cleaners may be used in lieu of those specified in Method No. 202A and Method No. 202E. Previously approved alternate...

L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...

K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...