Honeywell SPM20-00-02/70-00-01【完】共74篇
Honeywell 标准施工已经完结，涵盖DISASSEMBLY,CLEANING,INSPECTION,REPAIR,ASSEMBLY,PACKAGING
分类
子分类
排序
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-A.Method No. 403A: 阳极氧化铝和铝合金修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用A.Method No. 403A: Anodized Aluminum and Aluminum-alloy RepairMethod No. 403A: 阳极氧化铝和铝...
9月11日
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
11月15日
SECTION IV – REPAIR 5.清除钢制零件上的损伤-A.Method No. 405A:微小表面缺陷修复
5.Removing Damage from Steel Parts清除钢制零件上的损伤A.Method No. 405A: Minor Surface Defect RepairMethod No. 405A:微小表面缺陷修复Repair minor surface defects on steel parts as f...
10月1日
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-L.Method No. 403L: 修复因底漆和面漆损坏而暴露裸露镁的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用L.Method No. 403L: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
9月15日
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
11月22日
SECTION III – INSPECTION 1. Standard Inspection Practices -G. 目视检查
G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...
7月23日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-F.Method No. 407F: 松动、磨损或损坏的销钉（钢制零件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407F: Loose, Worn, or Damaged Pins (Steel Parts) ReplacementMethod No. 40...
11月3日SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-B.Method No. 403B: 硬铬镀件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用B.Method No. 403B: Hard Chrome Plated Parts RepairMethod No. 403B: 硬铬镀件修复NOTE: Hard chr...
9月12日
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
11月15日
SECTION IV – REPAIR 5.清除钢制零件上的损伤-B.Method No. 405B:去除严重腐蚀、硬碳、油漆和氧化皮
5.Removing Damage from Steel Parts清除钢制零件上的损伤B.Method No. 405B: Heavy Corrosion, Hard Carbon, Paint, and Scale RemovalMethod No. 405B:去除严重腐蚀、硬碳、油漆和氧化皮Remov...
10月1日
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-M.Method No. 403M:修复因底漆和面漆损坏而暴露裸露铝的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用M.Method No. 403M: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
9月15日
SECTION IV – ASSEMBLY 8-Marman卡箍（联轴器）安装
8.Marman Clamp (Coupling) InstallationMarman卡箍（联轴器）安装(1) Position clamp over mating component flanges as described in applicable manual.参照适用手册说明，将卡箍定位于配合...
11月22日SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...
7月25日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-G.Method No. 407G:松动、磨损或损坏的销钉（铝或镁零件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板G.Method No. 407G: Loose, Worn, or Damaged Pins (Aluminum or Magnesium Parts) Replacem...
11月3日SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-C.Method No.403C：薄而致密的镀铬零件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用C.Method No. 403C: Thin Dense Chrome Plated Parts RepairMethod No.403C：薄而致密的镀铬零件修...
9月13日
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
11月17日
SECTION IV – REPAIR 5.清除钢制零件上的损伤-C.Method No. 405C: 使用玻璃珠喷丸修复密封直径（唇形密封面）
5.Removing Damage from Steel Parts清除钢制零件上的损伤C.Method No. 405C: Seal Diameter (Lip Seal Surface) Repair Using Glass Bead PeeningMethod No. 405C: 使用玻璃珠喷丸修复密封直径...
10月1日
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-N.Method No. 403N: 铝的化学膜修补
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用N.Method No. 403N: Chemical Film Touch-Up of AluminumMethod No. 403N: 铝的化学膜修补(1) Remov...
9月22日
SECTION VI – PACKAGING – 包装（完）
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
11月22日
SECTION III – INSPECTION 1. Standard Inspection Practices -I.弧形联轴器检查
I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...
8月11日
