飞机维修工程管理-规章符合性
飞机维修工程管理-规章符合性 航空运营人要获得运行合格证，首先要通过局方针对CCAR-121《大型飞机公共航空运输承运人运行合格审定规则》运行合格审定。CCAR-121S是民航飞行标准...
飞机维修工程管理-适航限制项目(AWL)
适航限制项目(AWL)背景及定义：CCAR/FAR 25.571 结构的损伤容限和疲劳评定中要求，(3) 根据本条要求的评定，必须制订为预防灾难性破坏所必须的检查工作或其它程序，并必须将其载入第25.1529条...
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
SOPM20-10-07钛的机械加工
钛的机械加工MACHINING OF TITANIUM 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5492, and Boeing Operators Handbook 6M59-553, 'Machini...
HOEYWELL SECTION II – CLEANING 2. 清洁溶液的配制
2. Preparation of Cleaning Solutions 清洁溶液的配制WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATI...
A320neo HPV failed in OPEN position【转】
A320neo- HPV failed in OPEN position A320FAM neo - HPV failed in OPEN position leading to BLEED FAULT Engineering Support Applicability: A320FAM neo References: TFU 36.11.00.115...
航空发动机的种类-活塞式和喷气式发动机 Types of Aero-Engine-Piston and Jet Engines【转】
航空发动机为飞机提供飞行所需动力，民用主要有两种类型：活塞式发动机和喷气式发动机。 Aero-engines provide aircraft with the power required for flight. There are two main types of civ...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-A.Method No. 403A: 阳极氧化铝和铝合金修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用A.Method No. 403A: Anodized Aluminum and Aluminum-alloy RepairMethod No. 403A: 阳极氧化铝和铝...
一篇讲透737机组氧气的使用逻辑
引言：云端之上的生命保障在万米高空，现代客机为我们提供了舒适增压的客舱环境。但当飞机遭遇座舱失压等紧急情况时，一套可靠的氧气系统就成为了保障机组成员和乘客生命安全的最后防线。与大...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-B.Method No.407B：更换松动或损坏的螺纹钢丝螺套（铝或镁零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板B.Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Repla...
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
SOPM20-00-00 介绍
介绍INTRODUCTION The instructions in this manual tell how to do standard shop procedures during maintenance functions from simple checks and replacement to complete shop-type repai...
Honeywell-REPAIR修理
修理REPAIR 1. Planning Data 计划数据 A. Reason for the Job 工作原因 (1) Use these procedures for the modulating shutoff valve to replace defective parts and replace or repair de...
10101000 WASTE DRAIN VALVE ASSEMBLY【部件介绍】
排污活门10101000系列 一、名称 WASTE DRAIN VALVE ASSEMBLY 排污活门 二、件号 10101000CA,10101000C-A,10101000CG,10101000C-G,10101000CH,10101000C-H,10101000CJ,10101000C-J,10101000CA1,1...
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
Sealing Compounds
Sealing Compounds 密封化合物 Certain areas of all aircraft are sealed to withstand pressurization by air, to prevent leakage of fuel, to prevent passage of fumes, or to prevent cor...
SECTION III – INSPECTION 1. Standard Inspection Practices -N.复合材料部件
N.Composite Material Components复合材料部件(1) Check per Table 308.按照表308进行检查。
