SECTION I – DISASSEMBLY分解 TABLE OF CONTENTS 目录 SECTION 章节 1. Standard Disassembly Practices 标准分解操作 A. General 通用 B. Identification of Matched Parts and Sets 识别配合...

导电涂层的修理REPAIR OF CONDUCTIVE COATINGS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5837 for preparation of exterior plastic sur...

铜铍合金的机加工MACHINING OF COPPER BERYLLIUM ALLOYS   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5648. The airline has a copy of ...

激光沉积钛LASER DEPOSITED TITANIUM   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Material Specification BMS 7-361 for laser deposition of titanium. Access t...

印刷电路组件和元件板组件的修理REPAIR OF PRINTED CIRCUIT ASSEMBLIES AND COMPONENT BOARD ASSEMBLIES   1. INTRODUCTION 介绍 A. The data in this subject comes from the Boeing Process ...

电气终端和电气连接区的修理REPAIR OF ELECTRICAL TERMINATIONS AND ELECTRICAL BONDING AREAS   1. INTRODUCTION 介绍 A.The data in this subject comes from Boeing Process Specifications...

电气和电子元件标准维护说明ELECTRICAL AND ELECTRONIC COMPONENT STANDARD MAINTENANCE INSTRUCTIONS   1. INTRODUCTION 介绍 A. This subject gives general instructions for overhaul of a...

仪表盘电气模块通用信息INSTRUMENT PANEL ELECTRICAL MODULE GENERAL INFORMATION   1. INTRODUCTION 介绍 A. The airplane instrument panel contains electrical modules which have a basep...

缠绕导线电气连接的修理REPAIR OF WRAPPED WIRE ELECTRICAL CONNECTIONS   1. INTRODUCTION 介绍 A. A wrapped wire connection consists of a helix of continuous, solid, uninsulated wire ...

表面安装设备的拆除和更换REMOVAL AND REPLACEMENT OF SURFACE MOUNTED DEVICES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5128 (which s...

Sealing Compounds 密封化合物 Certain areas of all aircraft are sealed to withstand pressurization by air, to prevent leakage of fuel, to prevent passage of fumes, or to prevent cor...

Seals 密封 Seals are used to prevent fluid from passing a certain point, as well as to keep air and dirt out of the system in which they are used. The increased use of hydraulics a...

L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...

K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...

G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...

F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...

结构粘接前的最终清洗用溶剂（97系列）SOLVENTS FOR FINAL CLEANING BEFORE STRUCTURAL BONDING (SERIES 97)   1. GENERAL 通用 A. Thissubject contains a list of solvents for final clea...

通用清洗程序GENERAL CLEANING PROCEDURES  1. INTRODUCTION 介绍 A. The data in this subject comes from these Boeing Process Specifications: 本主题中的数据来自波音工艺规范： BAC5402,...