I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...

K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...

L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...

TABLE OF CONTENTS 目录 SECTION 章节 1. Standard Cleaning Practices 标准清洁规范 A. General 通用 2. Preparation of Cleaning Solutions 清洁溶液的配制 A. Method No. 202A: Alkaline Cle...

4. Alternate Cleaners 替代清洁剂 A. General 通用 (1) Alternate cleaners may be used in lieu of those specified in Method No. 202A and Method No. 202E. Previously approved alternate...

L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...

K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...

I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...

H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...

G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...

F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...

E. Bearing Inspection轴承检查(1) Separable Bearings:可分解的轴承。Table 301. Separable Bearing Defect Definitions表301 可分解轴承缺陷的定义Term项目Definition (Description of Defect...

SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...

结构粘接前的最终清洗用溶剂（97系列）SOLVENTS FOR FINAL CLEANING BEFORE STRUCTURAL BONDING (SERIES 97)   1. GENERAL 通用 A. Thissubject contains a list of solvents for final clea...

通用清洗程序GENERAL CLEANING PROCEDURES  1. INTRODUCTION 介绍 A. The data in this subject comes from these Boeing Process Specifications: 本主题中的数据来自波音工艺规范： BAC5402,...

金属一般清洗用溶剂（80系列）SOLVENTS FOR GENERAL CLEANING OF METAL(SERIES 80) 1. GENERAL 通用 A. This subject contains a list of solvents for general cleaning of metals as given in...

所有有机涂料的一般清洗用溶剂（81系列）SOLVENTS FOR GENERAL CLEANING OF ALL ORGANIC COATINGS (SERIES 81)   1. GENERAL 通用 A. This subject contains a list of solvents for general c...

耐溶剂有机涂料的一般清洗用溶剂（82系列）SOLVENTS FOR GENERAL CLEANING OF SOLVENT RESISTANT ORGANIC COATINGS (SERIES 82) 1. GENERAL 通用 A. This subject contains a list of solvents...

  复合材料一般清洗用溶剂（83系列）SOLVENTS FOR GENERAL CLEANING OF COMPOSITES (SERIES 83)   1. GENERAL 通用 A. This subject contains a list of solvents for general cleaning of c...

  喷涂前金属最终清洗的溶剂（84系列）SOLVENTS FOR FINAL CLEANING OF METAL BEFORE PAINTING (SERIES 84)   1. GENERAL 通用 A. This subject contains a list of solvents for final cl...

  喷涂前所有有机涂料最终清洗的溶剂（85系列）SOLVENTS FOR FINAL CLEANING OF ALL ORGANIC COATINGS BEFORE PAINTING (SERIES 85)   1. GENERAL 通用 A. This subject contains a list of...

  喷涂前抗溶剂有机涂层最终清洗的溶剂（86系列）SOLVENTS FOR FINAL CLEANING OF SOLVENT RESISTANT ORGANIC COATINGS BEFORE PAINTING (SERIES 86) 1. GENERAL 通用 A. This subject contai...