分类
子分类
排序
SOPM20-10-02合金钢的机械加工和应力消除
合金钢的机械加工和应力消除MACHINING OF ALLOY STEEL AND STRESS RELIEVING STEEL 1. INTRODUCTION 介绍 A.The data in this subject comes from Boeing Process Specifications BAC5436, B...
SOPM20-11-02电连接器的修理
电连接器的修理REPAIR OF ELECTRICAL CONNECTORS 1.INTRODUCTION 介绍 A.The following information is based on Boeing process specification BAC 5162 for assembly of electrical connec...
SOPM20-30-96氧气系统组件最终清洗的溶剂(96系列)
氧气系统组件最终清洗的溶剂(96系列)SOLVENTS FOR FINAL CLEANING OF OXYGEN SYSTEM COMPONENTS (SERIES 96) 1. GENERAL 通用 A. Thissubject contains a list of solvents for final cl...
SOPM20-50-04在钻孔中安装固定销和塞子
在钻孔中安装固定销和塞子INSTALLATION OF PERMANENT PINS AND PLUGS IN DRILL PASSAGES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5061 ...
SECTION IV – REPAIR 4. 修理铝制零件-B.Method No. 404B: 去除严重腐蚀、硬质碳、油漆和水垢
4. Repairing Aluminum Parts 修理铝制零件B.Method No. 404B: Heavy Corrosion, Hard Carbon, Paint, and Scale RemovalMethod No. 404B:去除严重腐蚀、硬质碳、油漆和水垢Remove heavy corros...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-H.Method No. 403H:镀银修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用H.Method No. 403H: Silver Plating RepairMethod No. 403H:镀银修复NOTE: If the type of silver p...
SECTION IV – ASSEMBLY 3-锥形密封件
3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...
SOPM20-20-01磁粉探伤
磁粉探伤MAGNETIC PARTICLE INSPECTION 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5424. The data about magnetic rubber comes from MIL...
SOPM20-42-03镀硬铬
镀硬铬HARD CHROME PLATING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5709. Access to the Boeing Process Specifications is availa...
SOPM20-50-15浇铸非金属垫片的安装
浇铸非金属垫片的安装INSTALLATION OF CASTABLE NON-METAL SHIMS 1. INTRODUCTION 介绍 A. This data in this subject comes from Boeing Process Document D042T613. The airline has or can g...
HOEYWELL SECTION II – CLEANING 4. 替代清洁剂
4. Alternate Cleaners 替代清洁剂A. General通用(1) Alternate cleaners may be used in lieu of those specified in Method No. 202A and Method No. 202E. Previously approved alternates a...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-B.Method No.407B:更换松动或损坏的螺纹钢丝螺套(铝或镁零件)
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板B.Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Repla...
航空开关知识和相关术语,switch,Microswitches,Relays
Switches 开关Switches control the current flow in most aircraft electrical circuits. A switch is used to start, to stop, or to change the direction of the current flow in the circu...
SOPM20-30-86喷涂前抗溶剂有机涂层最终清洗的溶剂(86系列)
喷涂前抗溶剂有机涂层最终清洗的溶剂(86系列)SOLVENTS FOR FINAL CLEANING OF SOLVENT RESISTANT ORGANIC COATINGS BEFORE PAINTING (SERIES 86) 1. GENERAL 通用 A. This subject contai...
SOPM20-43-03铝的化学转化涂层
铝的化学转化涂层CHEMICAL CONVERSION COATINGS FOR ALUMINUM 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5719. The airline has a co...
SOPM20-50-26如何应用防篡改腻子
如何应用防篡改腻子HOW TO APPLY TAMPER-PROOF PUTTY 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5459. The airline has a copy of the Bo...
SECTION III – INSPECTION 1. Standard Inspection Practices -O.设备和材料
O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...
SECTION IV – REPAIR 10. 铆接零件修复
10. Repairing Riveted Parts 铆接零件修复 A. Method No. 410A: Damaged Rivet Replacement General GuidelinesMethod No. 410A:损坏铆钉更换通用准则 (1) Replace damage rivets as follows: ...
SOPM20-11-03电气终端和电气连接区的修理
电气终端和电气连接区的修理REPAIR OF ELECTRICAL TERMINATIONS AND ELECTRICAL BONDING AREAS 1. INTRODUCTION 介绍 A.The data in this subject comes from Boeing Process Specifications...
SOPM20-30-97结构粘接前的最终清洗用溶剂(97系列)
结构粘接前的最终清洗用溶剂(97系列)SOLVENTS FOR FINAL CLEANING BEFORE STRUCTURAL BONDING (SERIES 97) 1. GENERAL 通用 A. Thissubject contains a list of solvents for final clea...






















