2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...

12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...

How to Use Torque Wrench (Standard Practices)如何使用扭矩扳手（标准操作规范）A torque wrench is a specialized tool designed to apply a specific amount of force to a fastener, suc...

仪表盘电气模块通用信息INSTRUMENT PANEL ELECTRICAL MODULE GENERAL INFORMATION   1. INTRODUCTION 介绍 A. The airplane instrument panel contains electrical modules which have a basep...

结构粘接前复合材料最终清洗的溶剂（99系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE STRUCTURAL BONDING (SERIES 99) 1. GENERAL 通用 A. This subject contains a list of solvent...

润滑LUBRICATION   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5008. The airline has a copy of the Boeing Process Specification Manu...

4. Repairing Aluminum Parts 修理铝制零件E.Method No. 404E: Minor Corrosion RepairMethod No. 404E:轻微腐蚀修复Remove minor corrosion from aluminum-alloy parts as follows:按如下步骤...

3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用K.Method No. 403K: Repair of Damaged Paint Coatings - Epoxy-Amine SystemsMethod No. 403K:修复...

6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...

保护层的剥离STRIPPING OF PROTECTIVE FINISHES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5725 and BAC5771 for stripping organic and...

电镀银SILVER PLATING   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5715. The airline has a copy of the Boeing Process Specification...

复合材料结构中的紧固件安装FASTENER INSTALLATION IN COMPOSITE STRUCTURES 1. INTRODUCTION 介绍 A. The data in this subject comes from BAC 5063. The airline has a copy of the Boeing P...

F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...

7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407E: Loose, Worn, or Damaged Bushings (Aluminum or Magnesium Parts) Repl...

热喷涂涂层的应用和表面处理APPLICATION AND FINISHING OF THERMAL SPRAY COATINGS   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5851 a...

非结构粘接前所有有机涂层最终清洗的溶剂（89系列）SOLVENTS FOR FINAL CLEANING OF ALL ORGANIC COATINGS BEFORE NON-STRUCTURAL BONDING (SERIES 89) 1. GENERAL 通用 A. This subject conta...

临时保护涂层TEMPORARY PROTECTIVE COATINGS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5034 which superseded BAC5835. The airline has...