分类
子分类
排序
SECTION IV – ASSEMBLY 4-压装过盈配合零件
4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...
2025-11-22
SOPM20-11-02电连接器的修理
2025-02-24
SOPM20-30-96氧气系统组件最终清洗的溶剂（96系列）
氧气系统组件最终清洗的溶剂（96系列）SOLVENTS FOR FINAL CLEANING OF OXYGEN SYSTEM COMPONENTS (SERIES 96) 1. GENERAL 通用 A. Thissubject contains a list of solvents for final cl...
2025-03-13
SOPM20-50-15浇铸非金属垫片的安装
浇铸非金属垫片的安装INSTALLATION OF CASTABLE NON-METAL SHIMS 1. INTRODUCTION 介绍 A. This data in this subject comes from Boeing Process Document D042T613. The airline has or can g...
2025-03-30
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
2025-06-14
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
2025-11-03
SPM 20-90-01波音氧气系统部件清洁工艺(Cobham)
2025-08-30
SOPM20-20-01磁粉探伤
磁粉探伤MAGNETIC PARTICLE INSPECTION 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5424. The data about magnetic rubber comes from MIL...
2025-03-07
SOPM20-42-03镀硬铬
镀硬铬HARD CHROME PLATING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5709. Access to the Boeing Process Specifications is availa...
2025-03-14
SOPM20-50-26如何应用防篡改腻子
如何应用防篡改腻子HOW TO APPLY TAMPER-PROOF PUTTY 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5459. The airline has a copy of the Bo...
2025-04-01
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
2025-09-02
SECTION IV – REPAIR 11-焊接零件修理
Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...
2025-11-07
如何使用扭矩扳手
How to Use Torque Wrench (Standard Practices)如何使用扭矩扳手（标准操作规范）A torque wrench is a specialized tool designed to apply a specific amount of force to a fastener, suc...
2026-05-20
SOPM20-30-86喷涂前抗溶剂有机涂层最终清洗的溶剂（86系列）
喷涂前抗溶剂有机涂层最终清洗的溶剂（86系列）SOLVENTS FOR FINAL CLEANING OF SOLVENT RESISTANT ORGANIC COATINGS BEFORE PAINTING (SERIES 86) 1. GENERAL 通用 A. This subject contai...
2025-03-10
SOPM20-43-03铝的化学转化涂层
铝的化学转化涂层CHEMICAL CONVERSION COATINGS FOR ALUMINUM 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5719. The airline has a co...
2025-03-18
SOPM20-50-05铝箔和其他标记的应用
铝箔和其他标记的应用APPLICATION OF ALUMINUM FOIL AND OTHER MARKERS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5305 and BAC5312. Th...
2025-03-21
SECTION IV – REPAIR 4. 修理铝制零件-D.Method No. 404D:燃油和滑油泵铝制壳体表面修复
4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...
2025-10-01
SECTION IV – REPAIR 3.防护涂料及电镀的修复与应用-J.Method No. 403J: 选择性电镀
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
2025-09-15
