7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板B.Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Repla...

Torque and Torque Wrenches 扭矩与扭矩扳手As the speed of an aircraft increases, each structural member becomes more highly stressed. It is therefore extremely important that each m...

高强度钢零件的修理和表面处理REPAIR AND REFINISH OF HIGH STRENGTH STEEL PARTS 1. INTRODUCTION 介绍 A.The procedures in this subject are applicable to high strength, low-alloy steel ...

  喷涂前所有有机涂料最终清洗的溶剂（85系列）SOLVENTS FOR FINAL CLEANING OF ALL ORGANIC COATINGS BEFORE PAINTING (SERIES 85)   1. GENERAL 通用 A. This subject contains a list of...

镁合金的阳极氧化处理ANODIZING OF MAGNESIUM ALLOYS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5734 and 5742. The airline has a copy...

如何在卡箍上安装螺栓固定件HOW TO INSTALL BOLT RETAINING HARDWARE ON CLAMPS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Part Standards BACC15AN and BACB19F, p...

O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...

10. Repairing Riveted Parts 铆接零件修复 A. Method No. 410A: Damaged Rivet Replacement General GuidelinesMethod No. 410A:损坏铆钉更换通用准则 (1) Replace damage rivets as follows: ...

How to Use Torque Wrench (Standard Practices)A torque wrench is a specialized tool designed to apply a specific amount of force to a fastener, such as a nut or bolt. This tool is...

  氧气系统组件最终清洗的溶剂（96系列）SOLVENTS FOR FINAL CLEANING OF OXYGEN SYSTEM COMPONENTS (SERIES 96) 1. GENERAL 通用 A. Thissubject contains a list of solvents for final cl...

在钻孔中安装固定销和塞子INSTALLATION OF PERMANENT PINS AND PLUGS IN DRILL PASSAGES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5061 ...

4. Repairing Aluminum Parts 修理铝制零件C.Method No. 404C: Gouge and Scoring RepairMethod No. 404C:沟槽和划痕修复Repair gouges, scoring, etc., on aluminum-alloy parts as follows:按...

3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用I.Method No. 403I: Electroless Nickel PlatingMethod No. 403I:化学镀镍CAUTION: BECAUSE OF MASK...

4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...

磁粉探伤MAGNETIC PARTICLE INSPECTION 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5424. The data about magnetic rubber comes from MIL...

镀硬铬HARD CHROME PLATING   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5709. Access to the Boeing Process Specifications is availa...

浇铸非金属垫片的安装INSTALLATION OF CASTABLE NON-METAL SHIMS 1. INTRODUCTION 介绍 A. This data in this subject comes from Boeing Process Document D042T613. The airline has or can g...