标准 第8页
分类
子分类
排序
SECTION IV – ASSEMBLY 4-压装过盈配合零件
4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...
11月22日
SOPM20-20-02渗透检测方法
渗透检测方法PENETRANT METHODS OF INSPECTION 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5423 and Boeing specification support standa...
3月8日
SOPM20-42-04电镀用铝合金的制备
电镀用铝合金的制备PREPARATION OF ALUMINUM ALLOYS FOR ELECTROPLATING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5714. The airline ha...
3月14日
SOPM20-50-16压接钢索的组装
压接钢索的组装ASSEMBLY OF SWAGED CABLES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5002. Access to the Boeing Process Specification...
3月30日
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
6月14日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
11月3日
紧固件扭矩（力矩）-扭矩与扭矩扳手-手柄加长是否影响力矩？？-开口销孔对齐
Torque and Torque Wrenches 扭矩与扭矩扳手As the speed of an aircraft increases, each structural member becomes more highly stressed. It is therefore extremely important that each m...
11月9日
SOPM20-10-03喷丸
喷丸SHOT PEENING 1. INTRODUCTION 介绍 A.The data in this subject comes from Boeing Process Specifications BAC5730, BAC5730-2 and BAC5951. Access to the Boeing Process Specificat...
2月9日
SOPM20-30-87喷涂前复合材料最终清洗的溶剂（87系列）
喷涂前复合材料最终清洗的溶剂（87系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE PAINTING (SERIES 87) 1. GENERAL 通用 A. This subject contains a list of solvents for...
3月11日
SOPM20-43-04电刷电镀、阳极氧化和电化学蚀刻
电刷电镀、阳极氧化和电化学蚀刻BRUSH PLATING, ANODIZING AND ELECTROCHEMICAL ETCHING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC 5...
3月18日
SOPM20-60-01清洁材料
清洁材料CLEANING MATERIALS 1. INTRODUCTION 介绍 A. Cleaning materials identified in the overhaul instructions are in this list. 大修说明中列出的清洁材料都在此清单中。 B. Vendor pro...
4月1日
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
9月2日
SECTION IV – REPAIR 11-焊接零件修理
Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...
11月7日SOPM20-11-04电气和电子元件标准维护说明
电气和电子元件标准维护说明ELECTRICAL AND ELECTRONIC COMPONENT STANDARD MAINTENANCE INSTRUCTIONS 1. INTRODUCTION 介绍 A. This subject gives general instructions for overhaul of a...
2月26日
SOPM20-30-98清洗聚合物、酚类和尼龙的溶剂（98和98-1系列）
清洗聚合物、酚类和尼龙的溶剂（98和98-1系列）SOLVENTS FOR CLEANING OF POLYMERICS, PHENOLICS AND NYLON (SERIES 98 AND 98-1) 1. GENERAL 通用 A. This subject contains a list of solvent...
3月13日
SOPM20-50-06O型圈和特氟龙密封的安装
O型圈和特氟龙密封的安装INSTALLATION OF O-RINGS AND TEFLON SEALS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5506 for installation...
3月22日
SECTION IV – REPAIR 4. 修理铝制零件-D.Method No. 404D:燃油和滑油泵铝制壳体表面修复
4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...
10月1日SECTION IV – REPAIR 3.防护涂料及电镀的修复与应用-J.Method No. 403J: 选择性电镀
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
9月15日
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
11月22日SOPM20-30-01轴承的清洁和再润滑
轴承的清洁和再润滑CLEANING AND RELUBRICATING BEARINGS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5040 and BAC5200, and field ex...
3月8日
