7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板 NOTE: Refer to Method No. 415A, and 415B for repairing damaged/oversized diameters w...

Switches 开关Switches control the current flow in most aircraft electrical circuits. A switch is used to start, to stop, or to change the direction of the current flow in the circu...

高强度钢零件的修理和表面处理REPAIR AND REFINISH OF HIGH STRENGTH STEEL PARTS 1. INTRODUCTION 介绍 A.The procedures in this subject are applicable to high strength, low-alloy steel ...

  喷涂前所有有机涂料最终清洗的溶剂（85系列）SOLVENTS FOR FINAL CLEANING OF ALL ORGANIC COATINGS BEFORE PAINTING (SERIES 85)   1. GENERAL 通用 A. This subject contains a list of...

镁合金的阳极氧化处理ANODIZING OF MAGNESIUM ALLOYS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5734 and 5742. The airline has a copy...

如何在卡箍上安装螺栓固定件HOW TO INSTALL BOLT RETAINING HARDWARE ON CLAMPS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Part Standards BACC15AN and BACB19F, p...

N.Composite Material Components复合材料部件(1) Check per Table 308.按照表308进行检查。

A.Method No. 409A: Enamel Paint Repair of PartsMethod No. 409A:零件搪瓷漆修复Repair painted surfaces of parts as follows:按以下步骤修复零件涂漆表面：(1) Prepare surfaces to be pain...

一份全面的航空部件无损检测（NDT）程序手册，详述了14项检测方法。涵盖射线检测（ASTM E1742）、超声波检测（MIL-STD-2154）、敲击测试、接触式蓝染、表面淬火层检测（MIL-STD-867）、硝酸盐蚀...

  氧气系统组件最终清洗的溶剂（96系列）SOLVENTS FOR FINAL CLEANING OF OXYGEN SYSTEM COMPONENTS (SERIES 96) 1. GENERAL 通用 A. Thissubject contains a list of solvents for final cl...

在钻孔中安装固定销和塞子INSTALLATION OF PERMANENT PINS AND PLUGS IN DRILL PASSAGES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5061 ...

4. Repairing Aluminum Parts 修理铝制零件B.Method No. 404B: Heavy Corrosion, Hard Carbon, Paint, and Scale RemovalMethod No. 404B:去除严重腐蚀、硬质碳、油漆和水垢Remove heavy corros...

3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用H.Method No. 403H: Silver Plating RepairMethod No. 403H:镀银修复NOTE: If the type of silver p...

3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...

详解航空高频同轴电缆插头/座与指示系统信号线插头/座的装配标准工艺。涵盖KINGS带保护同轴电缆插头（含小号型）、双层同轴电缆插头、K-LOC同轴电缆插头的制作与安装程序，以及指示系统防护插钉...

磁粉探伤MAGNETIC PARTICLE INSPECTION 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5424. The data about magnetic rubber comes from MIL...

镀硬铬HARD CHROME PLATING   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5709. Access to the Boeing Process Specifications is availa...