清洗聚合物、酚类和尼龙的溶剂（98和98-1系列）SOLVENTS FOR CLEANING OF POLYMERICS, PHENOLICS AND NYLON (SERIES 98 AND 98-1) 1. GENERAL 通用 A. This subject contains a list of solvent...

O型圈和特氟龙密封的安装INSTALLATION OF O-RINGS AND TEFLON SEALS   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5506 for installation...

4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...

3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...

5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...

详解航空继电器及继电器座的拆装标准施工工艺。涵盖10-60450前开锁继电器座、MIL-C-39029型继电器座、METHODE前退继电器座等多种型号的插孔拆除与安装方法、继电器钉夹接尺寸要求及安装规定，适...

轴承的清洁和再润滑CLEANING AND RELUBRICATING BEARINGS   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5040 and BAC5200, and field ex...

亮镉电镀BRIGHT CADMIUM PLATING   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5701 for cadmium plating, and BAC5849 for brush cadmi...

液压组件的防腐蚀处理程序CORROSION PROTECTION PROCEDURES FOR HYDRAULIC COMPONENTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification Control Dr...

E. Bearing Inspection轴承检查(1) Separable Bearings:可分解的轴承。Table 301. Separable Bearing Defect Definitions表301 可分解轴承缺陷的定义Term项目Definition (Description of Defect...

7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...

镀铬零件的研磨GRINDING OF CHROME PLATED PARTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5032. Access to the Boeing Process Specifi...

  非结构粘接前金属最终清洗的溶剂（88系列）SOLVENTS FOR FINAL CLEANING OF METAL BEFORE NON-STRUCTURAL BONDING (SERIES 88) 1. GENERAL 通用 A. This subject contains a list of solve...

专用涂料和饰面的应用APPLICATION OF SPECIAL PURPOSE COATINGS AND FINISHES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5710 and BAC58...

表面处理材料FINISHING MATERIALS 1. INTRODUCTION 介绍 A. Finishing materials identified in the overhaul instructions are in this list. 大修说明中确定的表面处理材料列于本清单中。 B. ...

2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...

12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...