喷丸SHOT PEENING   1. INTRODUCTION 介绍 A.The data in this subject comes from Boeing Process Specifications BAC5730, BAC5730-2 and BAC5951. Access to the Boeing Process Specificat...

  喷涂前复合材料最终清洗的溶剂（87系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE PAINTING (SERIES 87)   1. GENERAL 通用 A. This subject contains a list of solvents for...

电刷电镀、阳极氧化和电化学蚀刻BRUSH PLATING, ANODIZING AND ELECTROCHEMICAL ETCHING   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC 5...

清洁材料CLEANING MATERIALS 1. INTRODUCTION 介绍 A. Cleaning materials identified in the overhaul instructions are in this list. 大修说明中列出的清洁材料都在此清单中。 B. Vendor pro...

2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...

12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...

安全操作常识第一节 安全施工 做任何带高压有危险的电气/电子系统工作比如：——由带电导线接触而产生的电击；——由掉下的工具横在电气导线或导体之间造成的短路；——在现存易燃气体中产生电...

电气和电子元件标准维护说明ELECTRICAL AND ELECTRONIC COMPONENT STANDARD MAINTENANCE INSTRUCTIONS   1. INTRODUCTION 介绍 A. This subject gives general instructions for overhaul of a...

清洗聚合物、酚类和尼龙的溶剂（98和98-1系列）SOLVENTS FOR CLEANING OF POLYMERICS, PHENOLICS AND NYLON (SERIES 98 AND 98-1) 1. GENERAL 通用 A. This subject contains a list of solvent...

O型圈和特氟龙密封的安装INSTALLATION OF O-RINGS AND TEFLON SEALS   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5506 for installation...

4. Repairing Aluminum Parts 修理铝制零件E.Method No. 404E: Minor Corrosion RepairMethod No. 404E:轻微腐蚀修复Remove minor corrosion from aluminum-alloy parts as follows:按如下步骤...

3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用K.Method No. 403K: Repair of Damaged Paint Coatings - Epoxy-Amine SystemsMethod No. 403K:修复...

6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...

轴承的清洁和再润滑CLEANING AND RELUBRICATING BEARINGS   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5040 and BAC5200, and field ex...

亮镉电镀BRIGHT CADMIUM PLATING   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5701 for cadmium plating, and BAC5849 for brush cadmi...

液压组件的防腐蚀处理程序CORROSION PROTECTION PROCEDURES FOR HYDRAULIC COMPONENTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification Control Dr...

F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...

7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407E: Loose, Worn, or Damaged Bushings (Aluminum or Magnesium Parts) Repl...