分类
子分类
排序
SOPM20-10-06导电涂层的修理
导电涂层的修理REPAIR OF CONDUCTIVE COATINGS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5837 for preparation of exterior plastic sur...
2025-02-21
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
2025-06-14
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
2025-11-03
SPM 20-90-01波音氧气系统部件清洁工艺(Cobham)
2025-08-30
SOPM20-11-07表面安装设备的拆除和更换
表面安装设备的拆除和更换REMOVAL AND REPLACEMENT OF SURFACE MOUNTED DEVICES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5128 (which s...
2025-03-05
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
2025-09-02
SECTION IV – REPAIR 11-焊接零件修理
Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...
2025-11-07
How to Use Torque Wrench (Standard Practices)
How to Use Torque Wrench (Standard Practices)A torque wrench is a specialized tool designed to apply a specific amount of force to a fastener, such as a nut or bolt. This tool is...
2026-05-19
SECTION IV – REPAIR 4. 修理铝制零件-D.Method No. 404D:燃油和滑油泵铝制壳体表面修复
4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...
2025-10-01SECTION IV – REPAIR 3.防护涂料及电镀的修复与应用-J.Method No. 403J: 选择性电镀
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
2025-09-15
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
2025-11-22
第十章 继电器的拆装
详解航空继电器及继电器座的拆装标准施工工艺。涵盖10-60450前开锁继电器座、MIL-C-39029型继电器座、METHODE前退继电器座等多种型号的插孔拆除与安装方法、继电器钉夹接尺寸要求及安装规定，适...
2026-08-08
SOPM20-10-07钛的机械加工
钛的机械加工MACHINING OF TITANIUM 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5492, and Boeing Operators Handbook 6M59-553, 'Machini...
2025-02-21
SECTION III – INSPECTION 1. Standard Inspection Practices -E. 轴承检查
E. Bearing Inspection轴承检查(1) Separable Bearings:可分解的轴承。Table 301. Separable Bearing Defect Definitions表301 可分解轴承缺陷的定义Term项目Definition (Description of Defect...
2025-06-30
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-D.Method No. 407D:更换松动、磨损和/或损坏的衬套（钢制零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...
2025-11-03
SOPM20-50-22如何安装钢丝螺套
如何安装钢丝螺套HOW TO INSTALL THREADED INSERTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Standard BAC5064. The airline has a copy of the Boeing Pr...
2025-03-31
SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
2025-09-02
