标准 第5页
分类
子分类
排序
SOPM20-50-17液压组件的防腐蚀处理程序
液压组件的防腐蚀处理程序CORROSION PROTECTION PROCEDURES FOR HYDRAULIC COMPONENTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification Control Dr...
3月30日
SECTION III – INSPECTION 1. Standard Inspection Practices -E. 轴承检查
E. Bearing Inspection轴承检查(1) Separable Bearings:可分解的轴承。Table 301. Separable Bearing Defect Definitions表301 可分解轴承缺陷的定义Term项目Definition (Description of Defect...
6月30日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-D.Method No. 407D:更换松动、磨损和/或损坏的衬套（钢制零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...
11月3日
SOPM20-10-04镀铬零件的研磨
镀铬零件的研磨GRINDING OF CHROME PLATED PARTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5032. Access to the Boeing Process Specifi...
2月9日
SOPM20-30-88非结构粘接前金属最终清洗的溶剂（88系列）
非结构粘接前金属最终清洗的溶剂（88系列）SOLVENTS FOR FINAL CLEANING OF METAL BEFORE NON-STRUCTURAL BONDING (SERIES 88) 1. GENERAL 通用 A. This subject contains a list of solve...
3月11日
SOPM20-44-01专用涂料和饰面的应用
专用涂料和饰面的应用APPLICATION OF SPECIAL PURPOSE COATINGS AND FINISHES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5710 and BAC58...
3月20日
SOPM20-60-02表面处理材料
表面处理材料FINISHING MATERIALS 1. INTRODUCTION 介绍 A. Finishing materials identified in the overhaul instructions are in this list. 大修说明中确定的表面处理材料列于本清单中。 B. ...
4月1日
SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
9月2日
SECTION IV – REPAIR 12-动平衡操作规程与指南
12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...
11月12日
SOPM20-11-05仪表盘电气模块通用信息
仪表盘电气模块通用信息INSTRUMENT PANEL ELECTRICAL MODULE GENERAL INFORMATION 1. INTRODUCTION 介绍 A. The airplane instrument panel contains electrical modules which have a basep...
2月26日
SOPM20-30-99结构粘接前复合材料最终清洗的溶剂（99系列）
结构粘接前复合材料最终清洗的溶剂（99系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE STRUCTURAL BONDING (SERIES 99) 1. GENERAL 通用 A. This subject contains a list of solvent...
3月13日
SOPM20-50-07润滑
润滑LUBRICATION 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5008. The airline has a copy of the Boeing Process Specification Manu...
3月22日
SECTION IV – REPAIR 4. 修理铝制零件-E.Method No. 404E:轻微腐蚀修复
4. Repairing Aluminum Parts 修理铝制零件E.Method No. 404E: Minor Corrosion RepairMethod No. 404E:轻微腐蚀修复Remove minor corrosion from aluminum-alloy parts as follows:按如下步骤...
10月1日
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-K.Method No. 403K:修复受损的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用K.Method No. 403K: Repair of Damaged Paint Coatings - Epoxy-Amine SystemsMethod No. 403K:修复...
9月15日
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
11月22日
SOPM20-30-02保护层的剥离
保护层的剥离STRIPPING OF PROTECTIVE FINISHES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5725 and BAC5771 for stripping organic and...
3月9日SOPM20-42-06电镀银
电镀银SILVER PLATING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5715. The airline has a copy of the Boeing Process Specification...
3月15日
SOPM20-50-18复合材料结构中的紧固件安装
复合材料结构中的紧固件安装FASTENER INSTALLATION IN COMPOSITE STRUCTURES 1. INTRODUCTION 介绍 A. The data in this subject comes from BAC 5063. The airline has a copy of the Boeing P...
3月30日
SECTION III – INSPECTION 1. Standard Inspection Practices -F. 齿轮和花键检查
F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...
7月15日
