张群
飞机防冰系统-防冰部位和方法（Anti-icing Parts and Methods of Aircraft）【转】
飞机防冰系统-防冰部位和方法Aircraft Anti-icing System-Anti-icing Parts and Methods 飞机结冰会使飞机的空气动力性能变坏、发动机性能变坏、有关仪表读数不准，由此引起飞机的操纵性、稳定...
SOPM20-11-07表面安装设备的拆除和更换
表面安装设备的拆除和更换REMOVAL AND REPLACEMENT OF SURFACE MOUNTED DEVICES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5128 (which s...
部附件维修菜鸟到技术专家的成长之路
部附件维修行业对于从航空院校理科专业毕业的学生来说，不失为比较理想的就业方向之一。在这里，你可以学以致用，人尽其才，通过几年的努力，有机会成长为行业内的技术专家甚至管理者。...
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
飞机维修工程管理-波音737NG飞机持续适航文件介绍（一）
一、波音737NG飞机持续适航文件访问方法正常访问波音737NG飞机持续适航文件需要有波音网账号，运营波音公司飞机的运营人只要与波音签署的CSGTA，并缴纳一定的年费或通过购买飞机/其他软件(如m...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-D.Method No. 407D:更换松动、磨损和/或损坏的衬套（钢制零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
A320-36引气系统故障小结
一、发动机引气系统工作原理在发动机引气系统中，为了减少发动机的压力损失,通常是从发动机高压(HP)压气机的中间压力(IP)级（5级）引气。但当发动机低转速时,特别在飞机下降发动机在慢车状态时,...
如何使用扭矩扳手
How to Use Torque Wrench (Standard Practices)如何使用扭矩扳手（标准操作规范）A torque wrench is a specialized tool designed to apply a specific amount of force to a fastener, suc...
398B THERMOSTAT【部件介绍】
温控器398B 一、名称 THERMOSTAT 温控器 二、件号 398B050000,398B050000 Amdt A,398E020000,398E020000 Amdt A,398B060000,398E030000 三、章节号 36-11-35 四、适用机型 A330/A340 五、系统 3...
2780537 WING THERMAL ANTI-ICE PRESSURE REGULATING AND SHUTOFF VALVE ASSEMBLY
机翼热防冰压力调节和关断活门组件 一、名称 WING THERMAL ANTI-ICE PRESSURE REGULATING AND SHUTOFF VALVE ASSEMBLY 机翼热防冰压力调节和关断活门组件 二、件号 2780537-102~-104 三、章节号...
Seals,Packings,Backup Rings,Gaskets,Wipers
Seals 密封 Seals are used to prevent fluid from passing a certain point, as well as to keep air and dirt out of the system in which they are used. The increased use of hydraulics a...
SOPM 20-10-08 复合材料结构上表面密封的金属配件的拆除
复合材料结构上表面密封的金属配件的拆除REMOVAL OF FAYING SURFACE SEALED METAL FITTINGS FROM COMPOSITE STRUCTURES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing P...
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
SECTION IV – REPAIR 5.清除钢制零件上的损伤-B.Method No. 405B:去除严重腐蚀、硬碳、油漆和氧化皮
5.Removing Damage from Steel Parts清除钢制零件上的损伤B.Method No. 405B: Heavy Corrosion, Hard Carbon, Paint, and Scale RemovalMethod No. 405B:去除严重腐蚀、硬碳、油漆和氧化皮Remov...
SECTION IV – REPAIR 10. 铆接零件修复
10. Repairing Riveted Parts 铆接零件修复 A. Method No. 410A: Damaged Rivet Replacement General GuidelinesMethod No. 410A:损坏铆钉更换通用准则 (1) Replace damage rivets as follows: ...
sensor、transducer、transmitter是啥玩意儿
sensor 传感器sensor是一种设备或元件，它通过感知物理变量的变化来执行初始测量。传感器是一种与被测变量发生物理接触的装置，能够检测变化并输出相应的、可测量的信号。transducer 变送器（...
