一架飞机能用到的所有手册
一）飞机航线维修适用的手册：1、飞机维护手册AMM(Airplane/Aircraft Maintenance Manual)飞机和发动机制造厂所提供的维护手册，内容包括维护安装在飞机中的全部系统和功能部件的说明。飞机维护...
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
HOEYWELL SECTION I – DISASSEMBLY分解
SECTION I – DISASSEMBLY分解 TABLE OF CONTENTS 目录 SECTION 章节 1. Standard Disassembly Practices 标准分解操作 A. General 通用 B. Identification of Matched Parts and Sets 识别配合...
HOEYWELL SECTION II – CLEANING 3. Standard Cleaning Methods 标准清洁方法
3. Standard Cleaning Methods 标准清洁方法 CAUTION: SPECIFIED CLEANING METHODS OUTLINED MUST BE FOLLOWED. THE VARIOUS SOLUTIONS AND MATERIALS SPECIFIED IN THE CLEANING METHODS CAN B...
6764B(PRV)PRESSURE REGULATING VALVE
压力调节活门 一、名称 PRESSURE REGULATING VALVE 压力调节活门（4001HA）或 BLEED VALVE 引气活门 二、件号 6764B030000/6764B040000/6764B060000/6764B080000/6764C010000 三、章节号 36-11-...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-B.Method No. 403B: 硬铬镀件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用B.Method No. 403B: Hard Chrome Plated Parts RepairMethod No. 403B: 硬铬镀件修复NOTE: Hard chr...
SECTION IV – REPAIR 4.修理铝制零件-A.Method No. 404A:轻微表面缺陷修复
4.Repairing Aluminum Parts修理铝制零件A.Method No. 404A: Minor Surface Defect RepairMethod No. 404A:轻微表面缺陷修复Repair minor surface defects on aluminum-alloy parts as follows:...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
SOPM20-10-01高强度钢零件的修理和表面处理
高强度钢零件的修理和表面处理REPAIR AND REFINISH OF HIGH STRENGTH STEEL PARTS 1. INTRODUCTION 介绍 A.The procedures in this subject are applicable to high strength, low-alloy steel ...
SOPM20-11-03电气终端和电气连接区的修理
电气终端和电气连接区的修理REPAIR OF ELECTRICAL TERMINATIONS AND ELECTRICAL BONDING AREAS 1. INTRODUCTION 介绍 A.The data in this subject comes from Boeing Process Specifications...
107492 BLEED AIR REGULATOR【部件介绍】
引气调节器107492 一、名称 BLEED AIR REGULATOR 引气调节器BAR 二、件号 107492-1~-3,-5,-6,10-62008-10,-23,-37,-40,-41 三、章节号 36-13-95 四、适用机型 B737-300/-400/-500/-600/-700/-80...
二极管怎么区分正负极性？
二极管怎么区分正负极性？ 作为电子工程师，应该经常会有一个疑问，二极管极性判断方法有哪些？今天给大家讲一下二极管怎么分正负？ 法一：根据电路符号来区分二极管的极性 下图为大部分二极管...
空客A320飞机引气系统可靠性的提高
摘要:空客A320飞机引气系统故障率较高。本文介绍的飞机引气系统改进、引气系统健康监测以及引气系统实时故障诊断和健康管理等方法，可以有效地改善和提高A320飞机引气系统的可靠性，具有较强...
1.4 Joint Aircraft SystemComponent (JASC) Code联合飞机系统/组件(JASC)代码
Joint Aircraft SystemComponent (JASC) Code联合飞机系统/组件(JASC)代码The Joint Aircraft System/Component (JASC) Code table is a modified version of the Air Transport Association of...
飞机维修工程管理-审定维修要求(CMR)
审定维修要求（CMR）背景及定义：按照CCAR/FAR 25.1309要求，对运输类飞机的系统进行安全性分析和评估时，提出了故障探测要求，以防止危险性和灾难性故障发生。对这些要求经过进一步评审，被确...
SECTION IV – REPAIR 8-齿轮齿修复-A.Method No. 408A:齿轮齿渐开线表面轻微损伤修复
8. Repairing Gear Teeth齿轮齿修复A.Method No. 408A: Minor Gear Teeth Involute Surface Damage RepairMethod No. 408A:齿轮齿渐开线表面轻微损伤修复Repair minor surface damage on gear t...
