737NG发动机引气系统健康检查
737NG发动机引气系统健康检查 Engine Bleed Air System Health Check 一、工具设备及航材篇 1、引起测试设备(压力表、调压器、接头、堵头、软管、BAR启动器等) 2、高压气瓶 3、梅开扳手：3/8、3...
SOPM20-30-87喷涂前复合材料最终清洗的溶剂（87系列）
喷涂前复合材料最终清洗的溶剂（87系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE PAINTING (SERIES 87) 1. GENERAL 通用 A. This subject contains a list of solvents for...
开关知识和常用术语【转】
开关是一种控制电路中电流通断的装置，广泛用于家庭、工业和电子设备中。 1. 极和掷的命名约定 开关的基本功能用“极”和“掷”来描述： •极 (Pole)：表示开关的输入触点数量，或一个...
Seals,Packings,Backup Rings,Gaskets,Wipers
Seals 密封 Seals are used to prevent fluid from passing a certain point, as well as to keep air and dirt out of the system in which they are used. The increased use of hydraulics a...
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
SOPM20-30-96氧气系统组件最终清洗的溶剂（96系列）
氧气系统组件最终清洗的溶剂（96系列）SOLVENTS FOR FINAL CLEANING OF OXYGEN SYSTEM COMPONENTS (SERIES 96) 1. GENERAL 通用 A. Thissubject contains a list of solvents for final cl...
SOPM20-30-99结构粘接前复合材料最终清洗的溶剂（99系列）
结构粘接前复合材料最终清洗的溶剂（99系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE STRUCTURAL BONDING (SERIES 99) 1. GENERAL 通用 A. This subject contains a list of solvent...
Honeywell-INSPECTION/CHECK检查
检查INSPECTION/CHECK 1. Planning Data 计划数据 A. Reason for the Job 工作原因 (1) Use these procedures to find damage or worn parts and parts that show signs of near failure. 使...
HOEYWELL INTRODUCTION 介绍
INTRODUCTION介绍 1. General 通用 Information provided in this manual pertains to overhaul and repair processing for parts manufactured by Honeywell Inc., Phoenix, Arizona. 本手册提...
Sealing Compounds
Sealing Compounds 密封化合物 Certain areas of all aircraft are sealed to withstand pressurization by air, to prevent leakage of fuel, to prevent passage of fumes, or to prevent cor...
SOPM20-30-84耐溶剂有机涂料的一般清洗用溶剂（84系列）
喷涂前金属最终清洗的溶剂（84系列）SOLVENTS FOR FINAL CLEANING OF METAL BEFORE PAINTING (SERIES 84) 1. GENERAL 通用 A. This subject contains a list of solvents for final cl...
107494 REVERSE FLOW CHECK CONTROL VALVE（RFCC）
一、名称REVERSE FLOW CHECK CONTROL VALVE（RFCC）反流止回控制器二、件号107494-1~-4,S212N101-29N-45三、章节号36-11-83四、适用机型B757五、系统21 AIR CONDITIONING空调六、安装位置发动机...
SECTION IV – REPAIR 12-动平衡操作规程与指南
12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...
SOPM20-30-93燃油箱密封前的最终清洗用溶剂（93系列）
燃油箱密封前的最终清洗用溶剂（93系列）SOLVENTS FOR FINAL CLEANING BEFORE FUEL TANK SEALING (SERIES 93) 1. GENERAL 通用 A. This subject contains a listof solvents for final cleanin...
SECTION IV – REPAIR 11-焊接零件修理
Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...
SOPM20-30-86喷涂前抗溶剂有机涂层最终清洗的溶剂（86系列）
喷涂前抗溶剂有机涂层最终清洗的溶剂（86系列）SOLVENTS FOR FINAL CLEANING OF SOLVENT RESISTANT ORGANIC COATINGS BEFORE PAINTING (SERIES 86) 1. GENERAL 通用 A. This subject contai...
6777A020001 HIGH PRESSURE VALVE
高压活门一、名称HIGH PRESSURE VALVE高压活门二、件号6777A020001三、章节号36-10-20四、适用机型ARJ21五、系统36-气源系统六、安装位置发动机短舱区域七、部件原理高压活门(PN：6777A020001)...
SOPM20-43-04电刷电镀、阳极氧化和电化学蚀刻
电刷电镀、阳极氧化和电化学蚀刻BRUSH PLATING, ANODIZING AND ELECTROCHEMICAL ETCHING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC 5...
