飞机不得起飞的情况【转】
出现哪些情况飞机不得起飞？ Under what circumstances may the plane not take off? 有下列情况之一的，不得起飞： Aircraft are prohibited to take-off in any of the following circumstanc...
SECTION IV – REPAIR 12-动平衡操作规程与指南
12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...
表面处理的作用及注意事项
常见的表面处理方式可按“金属基材”“非金属基材（塑料、木材等）”分类，核心类型及特点如下：一、金属基材常用表面处理1. 电镀：将金属工件放入电镀液中，通过电解使金属离子附着在表面，形...
SECTION IV – ASSEMBLY 4-压装过盈配合零件
4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...
Honeywell-FITS AND CLEARANCES配合与间隙
配合与间隙FITS AND CLEARANCES Torque Values 扭矩值 (1) Tighten nuts, bolts, screws, and tube fittings to the standard torque unless specified differently. Refer to FAA Manual FAA-H...
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
各元器件在开关电源中的命名与用途【转】
各元器件在开关电源中的命名与用途开关电源的外围电路非常复杂，使用的元器件种类也比较繁多，性能各异。要想设计出性能高的开关电源就必须弄懂、弄通开关电源中各元器件的类型及主要功能。开关...
SOPM20-30-82耐溶剂有机涂料的一般清洗用溶剂（82系列）
耐溶剂有机涂料的一般清洗用溶剂（82系列）SOLVENTS FOR GENERAL CLEANING OF SOLVENT RESISTANT ORGANIC COATINGS (SERIES 82) 1. GENERAL 通用 A. This subject contains a list of solvents...
737NG-ATA 36 气源系统【系统原理】
ATA 36 气源系统 PNEUMATIC目录 1．介绍 2．部件安装位置 3．功能描述 4．分配介绍 5．发动机引气 1）介绍2）引气单向活门（5 级）3）高压级调节器/活门4）引气调节器 BAR 和压力调节及关断活门...
790390 FAN AIR TEMPERATURE SENSOR
一、名称FAN AIR TEMPERATURE SENSOR风扇空气温度传感器二、件号790390-1~-5,S210T120-108,-118三、章节号36-11-13四、适用机型B747/B767五、系统36-PNEUMATIC气动六、安装位置发动机吊架七、部...
一架飞机能用到的所有手册
一）飞机航线维修适用的手册：1、飞机维护手册AMM(Airplane/Aircraft Maintenance Manual)飞机和发动机制造厂所提供的维护手册，内容包括维护安装在飞机中的全部系统和功能部件的说明。飞机维护...
SOPM20-50-17液压组件的防腐蚀处理程序
液压组件的防腐蚀处理程序CORROSION PROTECTION PROCEDURES FOR HYDRAULIC COMPONENTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification Control Dr...
SOPM20-42-06电镀银
电镀银SILVER PLATING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5715. The airline has a copy of the Boeing Process Specification...
SOPM20-42-02低氢脆性镉钛合金电镀
低氢脆性镉钛合金电镀LOW HYDROGEN EMBRITTLEMENT CADMIUM - TITANIUM ALLOY PLATING 1. INTRODUCTION 介绍 NOTE: This low hydrogen embrittlement cadmium-titanium alloy plating is an o...
SOPM20-43-01铬酸阳极化
铬酸阳极化CHROMIC ACID ANODIZING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5019. The airline has a copy of the Boeing Process S...
SOPM20-43-02镁合金的阳极氧化处理
镁合金的阳极氧化处理ANODIZING OF MAGNESIUM ALLOYS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5734 and 5742. The airline has a copy...
SOPM20-50-04在钻孔中安装固定销和塞子
在钻孔中安装固定销和塞子INSTALLATION OF PERMANENT PINS AND PLUGS IN DRILL PASSAGES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5061 ...
