张群
Seals,Packings,Backup Rings,Gaskets,Wipers
Seals 密封 Seals are used to prevent fluid from passing a certain point, as well as to keep air and dirt out of the system in which they are used. The increased use of hydraulics a...
SECTION IV – REPAIR 6 -修理镁零件-A.Method No. 406A:轻微损坏修理
6.Repairing Magnesium Parts修理镁零件A.Method No. 406A: Minor Damage RepairMethod No. 406A:轻微损坏修理NOTE: Refer to Method No. 403L for repair of paint coatings for magnesium par...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-K.Method No. 403K:修复受损的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用K.Method No. 403K: Repair of Damaged Paint Coatings - Epoxy-Amine SystemsMethod No. 403K:修复...
SECTION IV – REPAIR 9-零件重新喷涂-零件搪瓷漆修复和环氧漆修复
A.Method No. 409A: Enamel Paint Repair of PartsMethod No. 409A:零件搪瓷漆修复Repair painted surfaces of parts as follows:按以下步骤修复零件涂漆表面：(1) Prepare surfaces to be pain...
Nut plate家族都有谁
一、Nut plate是谁？Nut plate（有时叫 anchor nut、plate nut），就是一种预先用铆钉固定在结构上的自锁螺母。以后再拧螺钉时，不需要人在背面拿扳手配合，只要从正面拧螺钉就可以完成紧固。它...
737NG-ATA 36 气源系统【系统原理】
ATA 36 气源系统 PNEUMATIC目录 1．介绍 2．部件安装位置 3．功能描述 4．分配介绍 5．发动机引气 1）介绍2）引气单向活门（5 级）3）高压级调节器/活门4）引气调节器 BAR 和压力调节及关断活门...
Honeywell-DISASSEMBLY分解
分解DISASSEMBLY 1. Planning Data 计划数据 A. Reason for the Job 工作原因 (1) Use these procedures to remove parts from the modulating shutoff valve to do the cleaning, checks, and ...
SOPM20-11-04电气和电子元件标准维护说明
电气和电子元件标准维护说明ELECTRICAL AND ELECTRONIC COMPONENT STANDARD MAINTENANCE INSTRUCTIONS 1. INTRODUCTION 介绍 A. This subject gives general instructions for overhaul of a...
AIR BLEED在A320CEO和A320NEO触发有啥不同？【转】
AIR BLEED维护信息在A320CEO和A320NEO触发在A320CEO和A320NEO触发有啥不同 事件背景 随着A320FAM飞机的更新换代，新一代的A320NEO飞机比A320CEO飞机有许多改进的地方，飞机的引气系统也不例外。...
飞机的防火部位 Fire Protection Parts of Aircraft【转】
飞机的防火部位Fire Protection Parts of Aircraft 飞机上需防火的区域主要包括发动机、APU、货舱、起落架舱、电子设备舱、驾驶舱、客舱及机翼和燃油箱等其它危险区域。飞机常见的防火系统如图1...
飞机维修工程管理-维修系统
一、维修机构设置要求 为落实适航性责任，确保飞机安全运行，CCAR 121.365合格证持有人的维修系统对航空营运人的维修系统做了概括性要求：任何合格证持有人应当建立一个由维修副总经理负责组织...
SECTION III – INSPECTION 1. Standard Inspection Practices -F. 齿轮和花键检查
F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...
塞尺的使用方法
塞尺的使用方法塞尺（也称为间隙规或厚薄规）是一种用于测量两个表面之间间隙的简单工具。它由一组厚度不同的金属片组成，每一片上通常标记有其厚度值。塞尺的结构 01 塞尺的结构 塞尺是由...
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
6730C010000 FAN AIR VALVE
一、名称FAN AIR VALVE风扇活门二、件号6730C010000,6730C010000 AMDT A,6730C010000 AMDT B,6730C010000 AMDT C三、章节号36-11-57四、适用机型A319, A320五、系统36-PNEUMATIC气动六、安装位...
