张群
SOPM20-50-15浇铸非金属垫片的安装
浇铸非金属垫片的安装INSTALLATION OF CASTABLE NON-METAL SHIMS 1. INTRODUCTION 介绍 A. This data in this subject comes from Boeing Process Document D042T613. The airline has or can g...
SOPM20-50-17液压组件的防腐蚀处理程序
液压组件的防腐蚀处理程序CORROSION PROTECTION PROCEDURES FOR HYDRAULIC COMPONENTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification Control Dr...
sensor、transducer、transmitter是啥玩意儿
sensor 传感器sensor是一种设备或元件，它通过感知物理变量的变化来执行初始测量。传感器是一种与被测变量发生物理接触的装置，能够检测变化并输出相应的、可测量的信号。transducer 变送器（...
SAS911 Wing Anti-Ice Control Valve
机翼防冰控制活门SAS911 一、名称 Wing Anti-Ice Control Valve 机翼防冰控制活门 二、件号 HC1750~HC1758,SAS911-001A,-002A,SAS912-001A,-002A 三、章节号 30-11-51 四、适用机型 A320 五、系...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-B.Method No.407B：更换松动或损坏的螺纹钢丝螺套（铝或镁零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板B.Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Repla...
SOPM20-11-08如何编程可编程电路设备
如何编程可编程电路设备HOW TO PROGRAM PROGRAMMABLE CIRCUIT DEVICES 1. INTRODUCTION 介绍 A. The data in this subject gives general procedures to put programs into Boeing-supplied pro...
A320-36引气系统故障小结
一、发动机引气系统工作原理在发动机引气系统中，为了减少发动机的压力损失,通常是从发动机高压(HP)压气机的中间压力(IP)级（5级）引气。但当发动机低转速时,特别在飞机下降发动机在慢车状态时,...
飞机维修工程管理-维修思想
按照什么思想来制订航空器的预定维修大纲并对它进行管理，是多年来人们一直研究的中心问题。纵观近百年的航空维修发展史，维修思想经历了由故障维修发展为预防性维修，通过不断的研究、进而完善...
6713D08 HP BLEED VALVE
一、名称HP BLEED VALVE高压引气活门（HPV）二、件号6713D080000,6713D080000 AMDT A三、章节号36-11-45四、适用机型A319/A320五、系统36-PNEUMATIC气动系统六、安装位置发动机短舱七、部件原理...
清洁 一 CLEANING
CAUTION: DO NOT USE THE MECHANICAL STANDARD PRACTICES MANUAL BY ITSELF. USE IT ONLY AS SPECIFIED IN THE APPLICABLE COMPONENT MAINTENANCE MANUAL OR OTHER FAA-APPROVED DOCUMENTS. 注...
SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...
SOPM20-50-16压接钢索的组装
压接钢索的组装ASSEMBLY OF SWAGED CABLES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5002. Access to the Boeing Process Specification...
SECTION IV – REPAIR 6 -修理镁零件-B.Method No. 406B:镁合金零件严重损坏修复
6.Repairing Magnesium Parts修理镁零件B.Method No. 406B: Magnesium-Alloy Parts Heavy Damage RepairMethod No. 406B:镁合金零件严重损坏修复Repair minor damage to magnesium-alloy parts ...
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
SECTION IV – REPAIR 6 -修理镁零件-A.Method No. 406A:轻微损坏修理
6.Repairing Magnesium Parts修理镁零件A.Method No. 406A: Minor Damage RepairMethod No. 406A:轻微损坏修理NOTE: Refer to Method No. 403L for repair of paint coatings for magnesium par...
