张群
SECTION IV – REPAIR 6 -修理镁零件-A.Method No. 406A:轻微损坏修理
6.Repairing Magnesium Parts修理镁零件A.Method No. 406A: Minor Damage RepairMethod No. 406A:轻微损坏修理NOTE: Refer to Method No. 403L for repair of paint coatings for magnesium par...
SECTION IV – REPAIR 9-零件重新喷涂-零件搪瓷漆修复和环氧漆修复
A.Method No. 409A: Enamel Paint Repair of PartsMethod No. 409A:零件搪瓷漆修复Repair painted surfaces of parts as follows:按以下步骤修复零件涂漆表面：(1) Prepare surfaces to be pain...
SECTION III – INSPECTION 1. Standard Inspection Practices -K.过滤器气泡点检查
K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...
SOPM20-30-01轴承的清洁和再润滑
轴承的清洁和再润滑CLEANING AND RELUBRICATING BEARINGS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5040 and BAC5200, and field ex...
211C117 PRESSURE SWITCHES【部件介绍】
压力开关211C117 一、名称 PRESSURE SWITCHES 压力开关 二、件号 211C117-222,-223 三、章节号 36-20-03 四、适用机型 B747 五、系统 36 PNEUMATIC 气源 六、安装位置 in the wing leading edge...
1266-100 DIFFERENTIAL PRESSURE SWITCH
一、名称DIFFERENTIAL PRESSURE SWITCH压差开关二、件号1266-100三、章节号52-73-12四、适用机型A320五、系统52-DOORS舱门六、安装位置811 客舱门和应急门位置七、部件原理压差开关主要是感应法...
SOPM20-11-10更换球栅阵列（BGA）零件
更换球栅阵列（BGA）零件REPLACEMENT OF BALL GRID ARRAY (BGA) PARTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Document D906-00016. 本主题中的数据来自波音文件...
6740F010000,6740G010000 OVERPRESSURE VALVE
一、名称OVERPRESSURE VALVE超压活门二、件号6740F010000,6740G010000三、章节号36-11-12四、适用机型A320五、系统36 PNEUMATIC气源六、安装位置发动机短舱七、部件原理Operation Fig FUNC-3工...
清洁 二 CLEANING
4. Abrasive Cleaning Procedures 磨料清洗程序 A. Deleted. 已删除。 B. Task 1: Dry Abrasive Blast 任务1：干式磨料喷砂 CAUTION: DO NOT USE DRY ABRASIVE BLAST ON SURFACES WITH 63 RA OR...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-I.Method No. 407I:松动、磨损或损坏的螺母板（铆接式）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板I.Method No. 407I: Loose, Worn or Damaged Nutplate (Riveted) ReplacementMethod No. 407...
SECTION III – INSPECTION 1. Standard Inspection Practices -G. 目视检查
G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...
SECTION IV – REPAIR 17-密封件修理（硅橡胶）
17. Repairing Seals (Silicone Rubber) 密封件（硅橡胶）修理 A. Method No. 417A: Repair of Disbonded Seals (Silicone Rubber)Method No.417A：脱胶密封件修理（硅橡胶） (1) Remove damage...
SECTION IV – REPAIR 6 -修理镁零件-C.Method No. 406C:镁合金零件的沟槽和划伤修复
6.Repairing Magnesium Parts修理镁零件C.Method No. 406C: Magnesium-Alloy Parts Gouge and Scoring RepairMethod No. 406C:镁合金零件的沟槽和划伤修复Repair minor damage to magnesium-all...
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-M.Method No. 403M:修复因底漆和面漆损坏而暴露裸露铝的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用M.Method No. 403M: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
HOEYWELL SECTION II – CLEANING 1. 标准清洁程序-通用
TABLE OF CONTENTS 目录SECTION 章节1. Standard Cleaning Practices标准清洁规范A. General通用2. Preparation of Cleaning Solutions清洁溶液的配制A. Method No. 202A: Alkaline Cleaning So...
HOEYWELL SECTION II – CLEANING 2. 清洁溶液的配制
2. Preparation of Cleaning Solutions 清洁溶液的配制WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATI...
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
