张群
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-E.Method No. 403E：干膜润滑剂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用E.Method No. 403E: Dry-film Lubricant RepairMethod No. 403E：干膜润滑剂修复Dry-film lubricant...
737NG-ATA 51 结构【系统原理】
目录1．一般描述2．复合材料1．一般描述 概述 这里有飞机的大体尺寸。 2．复合材料概述部分飞机结构和部件是复合材料制成的。这些材料有以下优点：高强度；防腐；增加疲劳寿命；减轻重量。
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-B.Method No. 403B: 硬铬镀件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用B.Method No. 403B: Hard Chrome Plated Parts RepairMethod No. 403B: 硬铬镀件修复NOTE: Hard chr...
航空维修必知：紧固件打保险丝标准与施工规范
航空维修必知：紧固件打保险丝标准与施工规范Part 1 引言紧固件是航空器核心连接零件，分为可拆卸紧固件与不可拆卸紧固件两类：可拆卸紧固件：拆卸后可重复使用，如螺栓、螺钉、螺帽、垫片等；...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-G.Method No. 403G:耐磨涂层表面磨损修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用G.Method No. 403G: Abradable Coating Surface Wear RepairMethod No. 403G:耐磨涂层表面磨损修复N...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-I.Method No. 403I:化学镀镍
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用I.Method No. 403I: Electroless Nickel PlatingMethod No. 403I:化学镀镍CAUTION: BECAUSE OF MASK...
SECTION III – INSPECTION 1. Standard Inspection Practices -F. 齿轮和花键检查
F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-L.Method No. 403L: 修复因底漆和面漆损坏而暴露裸露镁的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用L.Method No. 403L: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-F.Method No. 403F：等离子喷涂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用F.Method No. 403F: Plasma Spray RepairMethod No. 403F：等离子喷涂修复NOTE: Electric Arc Metal...
SECTION IV – REPAIR 4. 修理铝制零件-C.Method No. 404C:沟槽和划痕修复
4. Repairing Aluminum Parts 修理铝制零件C.Method No. 404C: Gouge and Scoring RepairMethod No. 404C:沟槽和划痕修复Repair gouges, scoring, etc., on aluminum-alloy parts as follows:按...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-A.Method No. 403A: 阳极氧化铝和铝合金修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用A.Method No. 403A: Anodized Aluminum and Aluminum-alloy RepairMethod No. 403A: 阳极氧化铝和铝...
SECTION III – INSPECTION 1. Standard Inspection Practices -M.用于电子设备校准和检查的热电偶模拟器
M.Thermocouple Simulators for Calibration and Checkout of Electronic Equipment 用于电子设备校准和检查的热电偶模拟器(1) For test purposes in simulating a thermocouple, a common and ...
