分类
子分类
排序
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-G.Method No. 403G:耐磨涂层表面磨损修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用G.Method No. 403G: Abradable Coating Surface Wear RepairMethod No. 403G:耐磨涂层表面磨损修复N...
2025-09-14
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-F.Method No. 403F：等离子喷涂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用F.Method No. 403F: Plasma Spray RepairMethod No. 403F：等离子喷涂修复NOTE: Electric Arc Metal...
2025-09-14SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-E.Method No. 403E：干膜润滑剂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用E.Method No. 403E: Dry-film Lubricant RepairMethod No. 403E：干膜润滑剂修复Dry-film lubricant...
2025-09-14
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-D.Method No.403D：金属喷涂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用D.Method No. 403D: Metal Spray RepairMethod No.403D：金属喷涂修复NOTE: Electric Arc Spray and...
2025-09-14
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-C.Method No.403C：薄而致密的镀铬零件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用C.Method No. 403C: Thin Dense Chrome Plated Parts RepairMethod No.403C：薄而致密的镀铬零件修...
2025-09-13
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-B.Method No. 403B: 硬铬镀件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用B.Method No. 403B: Hard Chrome Plated Parts RepairMethod No. 403B: 硬铬镀件修复NOTE: Hard chr...
2025-09-12SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-A.Method No. 403A: 阳极氧化铝和铝合金修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用A.Method No. 403A: Anodized Aluminum and Aluminum-alloy RepairMethod No. 403A: 阳极氧化铝和铝...
2025-09-11
SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
2025-09-02
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
2025-09-02
SPM 20-90-01波音氧气系统部件清洁工艺(Cobham)
2025-08-30
SECTION III – INSPECTION 1. Standard Inspection Practices -O.设备和材料
O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...
2025-08-29
SECTION III – INSPECTION 1. Standard Inspection Practices -N.复合材料部件
N.Composite Material Components复合材料部件(1) Check per Table 308.按照表308进行检查。
2025-08-20
SECTION III – INSPECTION 1. Standard Inspection Practices -M.用于电子设备校准和检查的热电偶模拟器
M.Thermocouple Simulators for Calibration and Checkout of Electronic Equipment 用于电子设备校准和检查的热电偶模拟器(1) For test purposes in simulating a thermocouple, a common and ...
2025-08-19
SECTION III – INSPECTION 1. Standard Inspection Practices -L.压降检查：清洁的金属滤芯
L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...
2025-08-18
SECTION III – INSPECTION 1. Standard Inspection Practices -K.过滤器气泡点检查
K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...
2025-08-18
SECTION III – INSPECTION 1. Standard Inspection Practices -I.弧形联轴器检查
I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...
2025-08-11
SOPM目录【标准大修施工手册】
目录 TABLE OF CONTENTSINTRODUCTION 介绍A. The Standard Overhaul Practices Manual (SOPM), Document D6-51702, includes a Title Page, a Revision Record, a Transmittal Letter, a List o...
2025-08-02
SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...
2025-07-25
