1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...

1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...

Cleaning Process for Boeing Oxygen System Components-Standard Practice Manual丨波音氧气系统部件清洁工艺-标准操作手册 TABLE OF CONTENTS CLEANING PROCESS 1. Scope 2. General Recommen...

O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...

O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...

N.Composite Material Components复合材料部件(1) Check per Table 308.按照表308进行检查。

N.Composite Material Components 复合材料部件 (1) Check per Table 308. 按照表308进行检查。

M.Thermocouple Simulators for Calibration and Checkout of Electronic Equipment 用于电子设备校准和检查的热电偶模拟器(1) For test purposes in simulating a thermocouple, a common and ...

M.Thermocouple Simulators for Calibration and Checkout of Electronic Equipment 用于电子设备校准和检查的热电偶模拟器 (1) For test purposes in simulating a thermocouple, a common and...

L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...

L.Pressure Drop Check: Cleaned Metallic Filter Elements压降检查：清洁的金属滤芯Check pressure drop of cleaned filter element as follows:检查清洁后的滤芯压降，方法如下：NOTE: Check ...

K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...

K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...

I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...

I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...

目录 TABLE OF CONTENTSINTRODUCTION 介绍A. The Standard Overhaul Practices Manual (SOPM), Document D6-51702, includes a Title Page, a Revision Record, a Transmittal Letter, a List o...

H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...

H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...

G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...

G. Visual Inspection 目视检查 (1) General Information 通用信息 (a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause...

Seals 密封 Seals are used to prevent fluid from passing a certain point, as well as to keep air and dirt out of the system in which they are used. The increased use of hydraulics a...

Sealing Compounds 密封化合物 Certain areas of all aircraft are sealed to withstand pressurization by air, to prevent leakage of fuel, to prevent passage of fumes, or to prevent cor...