737NG发动机引气系统健康检查
737NG发动机引气系统健康检查 Engine Bleed Air System Health Check 一、工具设备及航材篇 1、引起测试设备(压力表、调压器、接头、堵头、软管、BAR启动器等) 2、高压气瓶 3、梅开扳手：3/8、3...
飞机维修工程管理-维修思想
按照什么思想来制订航空器的预定维修大纲并对它进行管理，是多年来人们一直研究的中心问题。纵观近百年的航空维修发展史，维修思想经历了由故障维修发展为预防性维修，通过不断的研究、进而完善...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-I.Method No. 403I:化学镀镍
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用I.Method No. 403I: Electroless Nickel PlatingMethod No. 403I:化学镀镍CAUTION: BECAUSE OF MASK...
A320-30防冰防雨【系统原理】
A320-Single Aisle-TECHNICAL TRAINING MANUAL-T1 (CFM 56) (Lvl 2&3)ICE & RAIN PROTECTION-30章 防冰和防雨系统ICE & RAIN PROTECTIONGENERALIce and Rain Protection System Com...
飞机不得起飞的情况【转】
出现哪些情况飞机不得起飞？ Under what circumstances may the plane not take off? 有下列情况之一的，不得起飞： Aircraft are prohibited to take-off in any of the following circumstanc...
深度尺的读数及使用方法
深度游标尺是一种专用于测量凹槽、孔洞、盲孔深度以及阶梯形工件等内部尺寸的测量工具。 01 深度尺的结构原理 深度游标尺结构如下图所示，，它的结构特点是尺框3的两个量爪连成一起成为一...
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
SECTION IV – REPAIR 6 -修理镁零件-C.Method No. 406C:镁合金零件的沟槽和划伤修复
6.Repairing Magnesium Parts修理镁零件C.Method No. 406C: Magnesium-Alloy Parts Gouge and Scoring RepairMethod No. 406C:镁合金零件的沟槽和划伤修复Repair minor damage to magnesium-all...
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
3505920 TGA/MSOV/ISOLATOR ASSEMBLY
一、名称TGA/MSOV/ISOLATOR ASSEMBLY涡轮齿轮箱/调节关断活门/隔离器组件二、件号3505920-5~-9三、章节号29-11-25四、适用机型B777-200五、系统29 HYDRAULIC POWER液压六、安装位置the left win...
航空发动机的种类-活塞式和喷气式发动机 Types of Aero-Engine-Piston and Jet Engines【转】
航空发动机为飞机提供飞行所需动力，民用主要有两种类型：活塞式发动机和喷气式发动机。 Aero-engines provide aircraft with the power required for flight. There are two main types of civ...
飞机维修工程管理-持续适航文件
一、持续适航文件(ICA)的定义FAA Order 8110.54A中关于ICA的定义描述为:“Instructions for Continued Airworthiness (ICA).Documentation that gives instructions and requirements for the m...
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-B.Method No.407B：更换松动或损坏的螺纹钢丝螺套（铝或镁零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板B.Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Repla...
SECTION IV – ASSEMBLY 3-锥形密封件
3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...
1266-100 DIFFERENTIAL PRESSURE SWITCH
一、名称DIFFERENTIAL PRESSURE SWITCH压差开关二、件号1266-100三、章节号52-73-12四、适用机型A320五、系统52-DOORS舱门六、安装位置811 客舱门和应急门位置七、部件原理压差开关主要是感应法...
