SECTION IV – REPAIR 修理（三）-J.Method No. 403J: Selective Electroplating
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-K.Method No. 403K:修复受损的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用K.Method No. 403K: Repair of Damaged Paint Coatings - Epoxy-Amine SystemsMethod No. 403K:修复...
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
737NG-30防冰防雨【系统原理】
737NG-TECHNICAL TRAINING MANUAL技术培训手册ATA 30 防冰防雨目录1．介绍2．一般描述3．机翼防冰1）介绍2）部件位置3）防冰面板4）防冰活门5）地面过热电门6）伸缩管7）操纵台机翼防冰电门8）...
3215394 Modulating shutoff valve (MSOV)
调节关断活门一、名称Modulating shutoff valve (MSOV)调节关断活门二、件号3215394-3~8三、章节号29-20-17四、适用机型B777五、系统29 HYDRAULIC POWER液压六、安装位置Zone 197, Aft Wing-to-...
千分尺读数及使用方法
千分尺读数及使用方法 在机械领域，针对微米(um)级别的高精度零件测量与检测，传统的游标卡尺往往难以达到所需的精确度。此时，千分尺成为了不可或缺的精密测量工具。 01 外径千分尺及其...
SECTION III – INSPECTION 1. Standard Inspection Practices -F. 齿轮和花键检查
F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...
ANTI ICE ENG1（2） VALVE CLSD故障分析-CFM56
1.背景B-XXXX飞机监控到有ANTI ICE ENG1 VALVE CLSD信息，航后更换1发防冰活门，试车故障依旧；进一步检查发现防冰活门连接的SENSELINE有漏气，更换漏气的软管后，试车正常。2.原理CFM56发动机...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-D.Method No. 407D:更换松动、磨损和/或损坏的衬套（钢制零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
