张群
飞机维修工程管理-维修思想
按照什么思想来制订航空器的预定维修大纲并对它进行管理，是多年来人们一直研究的中心问题。纵观近百年的航空维修发展史，维修思想经历了由故障维修发展为预防性维修，通过不断的研究、进而完善...
6713D08 HP BLEED VALVE
一、名称HP BLEED VALVE高压引气活门（HPV）二、件号6713D080000,6713D080000 AMDT A三、章节号36-11-45四、适用机型A319/A320五、系统36-PNEUMATIC气动系统六、安装位置发动机短舱七、部件原理...
SAS911 Wing Anti-Ice Control Valve
机翼防冰控制活门SAS911 一、名称 Wing Anti-Ice Control Valve 机翼防冰控制活门 二、件号 HC1750~HC1758,SAS911-001A,-002A,SAS912-001A,-002A 三、章节号 30-11-51 四、适用机型 A320 五、系...
1266-100 DIFFERENTIAL PRESSURE SWITCH
一、名称DIFFERENTIAL PRESSURE SWITCH压差开关二、件号1266-100三、章节号52-73-12四、适用机型A320五、系统52-DOORS舱门六、安装位置811 客舱门和应急门位置七、部件原理压差开关主要是感应法...
为什么要创建这个博客？
以前很少动笔写东西，也几乎没有认真做过总结。生活里的琐碎、工作上的点滴，大多随风而去，回头看时，竟找不到几件值得回味的往事。职业规划更是模糊，日子一天天过，却总觉得少了点什么。后来...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-B.Method No.407B：更换松动或损坏的螺纹钢丝螺套（铝或镁零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板B.Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Repla...
SECTION III – INSPECTION 1. Standard Inspection Practices -E. 轴承检查
E. Bearing Inspection轴承检查(1) Separable Bearings:可分解的轴承。Table 301. Separable Bearing Defect Definitions表301 可分解轴承缺陷的定义Term项目Definition (Description of Defect...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-M.Method No. 403M:修复因底漆和面漆损坏而暴露裸露铝的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用M.Method No. 403M: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
SECTION III – INSPECTION 1. Standard Inspection Practices -K.过滤器气泡点检查
K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...
211C117 PRESSURE SWITCHES【部件介绍】
压力开关211C117 一、名称 PRESSURE SWITCHES 压力开关 二、件号 211C117-222,-223 三、章节号 36-20-03 四、适用机型 B747 五、系统 36 PNEUMATIC 气源 六、安装位置 in the wing leading edge...
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
SOPM20-50-16压接钢索的组装
压接钢索的组装ASSEMBLY OF SWAGED CABLES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5002. Access to the Boeing Process Specification...
SECTION III – INSPECTION 1. Standard Inspection Practices -G. 目视检查
G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-I.Method No. 407I:松动、磨损或损坏的螺母板（铆接式）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板I.Method No. 407I: Loose, Worn or Damaged Nutplate (Riveted) ReplacementMethod No. 407...
737NG-ATA 56 窗户【系统原理】
基于737NG技术培训手册，详解ATA56章窗户系统工作原理。涵盖驾驶舱1-5号风挡（固定与活动2号风挡）的层状玻璃/乙烯树脂结构、导电加热膜及防冰除雾原理；客舱窗户与应急出口窗户的承力结构（外...
HOEYWELL SECTION II – CLEANING 3. Standard Cleaning Methods 标准清洁方法
3. Standard Cleaning Methods 标准清洁方法 CAUTION: SPECIFIED CLEANING METHODS OUTLINED MUST BE FOLLOWED. THE VARIOUS SOLUTIONS AND MATERIALS SPECIFIED IN THE CLEANING METHODS CAN B...
