张群
SECTION IV – REPAIR 5.清除钢制零件上的损伤-A.Method No. 405A:微小表面缺陷修复
5.Removing Damage from Steel Parts清除钢制零件上的损伤A.Method No. 405A: Minor Surface Defect RepairMethod No. 405A:微小表面缺陷修复Repair minor surface defects on steel parts as f...
SECTION IV – REPAIR 5.清除钢制零件上的损伤-C.Method No. 405C: 使用玻璃珠喷丸修复密封直径（唇形密封面）
5.Removing Damage from Steel Parts清除钢制零件上的损伤C.Method No. 405C: Seal Diameter (Lip Seal Surface) Repair Using Glass Bead PeeningMethod No. 405C: 使用玻璃珠喷丸修复密封直径...
SECTION IV – REPAIR 3.防护涂料及电镀的修复与应用-J.Method No. 403J: 选择性电镀
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-E.Method No. 407E: 松动、磨损或损坏的衬套（铝或镁部件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407E: Loose, Worn, or Damaged Bushings (Aluminum or Magnesium Parts) Repl...
HOEYWELL SECTION II – CLEANING 3. Standard Cleaning Methods 标准清洁方法
3. Standard Cleaning Methods 标准清洁方法 CAUTION: SPECIFIED CLEANING METHODS OUTLINED MUST BE FOLLOWED. THE VARIOUS SOLUTIONS AND MATERIALS SPECIFIED IN THE CLEANING METHODS CAN B...
SECTION III – INSPECTION 1. Standard Inspection Practices -O.设备和材料
O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...
SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
FE256 EMERGENCY DOOR DAMPER ACTUATOR
一、名称EMERGENCY DOOR DAMPER ACTUATOR应急门阻尼作动器二、件号FE256-000,FE256-000 Amdt A,FE256-001,FE256-001 Amdt A三、章节号52-11-07四、适用机型A330五、系统52 DOORS舱门六、安装位...
737NG-ATA 56 窗户【系统原理】
WINDOWS目录1．介绍2．驾驶舱风挡介绍3．驾驶舱固定风挡1）1＃风挡 2）3＃风挡 3）4＃、5＃风挡 4．驾驶舱活动风挡1）2＃活动风挡5．客舱窗户一般描述6．应急出口窗户一般描述7．机舱门观...
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
SECTION IV – REPAIR 8-齿轮齿修复-A.Method No. 408A:齿轮齿渐开线表面轻微损伤修复
8. Repairing Gear Teeth齿轮齿修复A.Method No. 408A: Minor Gear Teeth Involute Surface Damage RepairMethod No. 408A:齿轮齿渐开线表面轻微损伤修复Repair minor surface damage on gear t...
360人工智能研究院在航司领域翻译上取得关键成果
近日，360人工智能研究院在航司领域翻译技术研发上取得关键成果，精准解决航司专业翻译痛点，为航司运营合规、效率提升注入硬核支撑，目前相关解决方案已作为标准化产品，向多家航司全面推广落...
SECTION IV – REPAIR 4. 修理铝制零件-D.Method No. 404D:燃油和滑油泵铝制壳体表面修复
4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-D.Method No.403D：金属喷涂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用D.Method No. 403D: Metal Spray RepairMethod No.403D：金属喷涂修复NOTE: Electric Arc Spray and...
SECTION III – INSPECTION 1. Standard Inspection Practices -F. 齿轮和花键检查
F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...
