SECTION IV – REPAIR 6 -修理镁零件-C.Method No. 406C:镁合金零件的沟槽和划伤修复
6.Repairing Magnesium Parts修理镁零件C.Method No. 406C: Magnesium-Alloy Parts Gouge and Scoring RepairMethod No. 406C:镁合金零件的沟槽和划伤修复Repair minor damage to magnesium-all...
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
3505920 TGA/MSOV/ISOLATOR ASSEMBLY
一、名称TGA/MSOV/ISOLATOR ASSEMBLY涡轮齿轮箱/调节关断活门/隔离器组件二、件号3505920-5~-9三、章节号29-11-25四、适用机型B777-200五、系统29 HYDRAULIC POWER液压六、安装位置the left win...
航空发动机的种类-活塞式和喷气式发动机 Types of Aero-Engine-Piston and Jet Engines【转】
航空发动机为飞机提供飞行所需动力，民用主要有两种类型：活塞式发动机和喷气式发动机。 Aero-engines provide aircraft with the power required for flight. There are two main types of civ...
飞机维修工程管理-持续适航文件
一、持续适航文件(ICA)的定义FAA Order 8110.54A中关于ICA的定义描述为:“Instructions for Continued Airworthiness (ICA).Documentation that gives instructions and requirements for the m...
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-B.Method No.407B：更换松动或损坏的螺纹钢丝螺套（铝或镁零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板B.Method No. 407B: Loose or Damaged Thread Inserts (Aluminum or Magnesium Parts) Repla...
SECTION IV – ASSEMBLY 3-锥形密封件
3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...
1266-100 DIFFERENTIAL PRESSURE SWITCH
一、名称DIFFERENTIAL PRESSURE SWITCH压差开关二、件号1266-100三、章节号52-73-12四、适用机型A320五、系统52-DOORS舱门六、安装位置811 客舱门和应急门位置七、部件原理压差开关主要是感应法...
各元器件在开关电源中的命名与用途【转】
各元器件在开关电源中的命名与用途开关电源的外围电路非常复杂，使用的元器件种类也比较繁多，性能各异。要想设计出性能高的开关电源就必须弄懂、弄通开关电源中各元器件的类型及主要功能。开关...
关于件号为6740G010000的OPV的维修提示
维修提示 MAINTENANCE TIPS背景及现象BACKGROUND OR PHENOMENON新引进B-303M和B-302Y两架飞机四个发动机引气系统有三个均出现“AIR ENG2 BLEED ABNORM PR”的警告信息，并伴有“OVPRESS-V 5HA2/...
表面处理的作用及注意事项
常见的表面处理方式可按“金属基材”“非金属基材（塑料、木材等）”分类，核心类型及特点如下：一、金属基材常用表面处理1. 电镀：将金属工件放入电镀液中，通过电解使金属离子附着在表面，形...
SECTION IV – REPAIR 3.防护涂料及电镀的修复与应用-J.Method No. 403J: 选择性电镀
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
SECTION IV – REPAIR 8-齿轮齿修复-A.Method No. 408A:齿轮齿渐开线表面轻微损伤修复
8. Repairing Gear Teeth齿轮齿修复A.Method No. 408A: Minor Gear Teeth Involute Surface Damage RepairMethod No. 408A:齿轮齿渐开线表面轻微损伤修复Repair minor surface damage on gear t...
3399100 HIGH PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLER/HPFAC – high pressure fan air controller
一、名称HIGH PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLERHPFAC - high pressure fan air controller高压调节器及关断活门控制器HPFAC - 高压风扇控制器(在七、部件原理和九、在飞机系统...
航空器分类 Classification of Aircraft【转】
航空器的分类Classification of Aircraft 一、按照航空器的大小分类 Classification according to aircraft size 最大起飞重量 60000 千克（不含）以上的航空器是大型航空器； Aircraft with a ...
SOPM目录【标准大修施工手册】
目录 TABLE OF CONTENTSINTRODUCTION 介绍A. The Standard Overhaul Practices Manual (SOPM), Document D6-51702, includes a Title Page, a Revision Record, a Transmittal Letter, a List o...
