张群
SOPM20-50-16压接钢索的组装
压接钢索的组装ASSEMBLY OF SWAGED CABLES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5002. Access to the Boeing Process Specification...
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
SOPM20-11-10更换球栅阵列（BGA）零件
更换球栅阵列（BGA）零件REPLACEMENT OF BALL GRID ARRAY (BGA) PARTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Document D906-00016. 本主题中的数据来自波音文件...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-M.Method No. 403M:修复因底漆和面漆损坏而暴露裸露铝的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用M.Method No. 403M: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
211C117 PRESSURE SWITCHES【部件介绍】
压力开关211C117 一、名称 PRESSURE SWITCHES 压力开关 二、件号 211C117-222,-223 三、章节号 36-20-03 四、适用机型 B747 五、系统 36 PNEUMATIC 气源 六、安装位置 in the wing leading edge...
Electrical Bonding vs. Grounding vs. Earthing
Electrical Bonding vs. Grounding vs. Earthing 电气搭接 vs. 接地 vs. 接大地Understanding the difference between bonding, grounding, and earthing is essential to safety in aviation. ...
360人工智能研究院在航司领域翻译上取得关键成果
近日，360人工智能研究院在航司领域翻译技术研发上取得关键成果，精准解决航司专业翻译痛点，为航司运营合规、效率提升注入硬核支撑，目前相关解决方案已作为标准化产品，向多家航司全面推广落...
SECTION IV – REPAIR 17-密封件修理（硅橡胶）
17. Repairing Seals (Silicone Rubber) 密封件（硅橡胶）修理 A. Method No. 417A: Repair of Disbonded Seals (Silicone Rubber)Method No.417A：脱胶密封件修理（硅橡胶） (1) Remove damage...
SECTION IV – REPAIR 6 -修理镁零件-A.Method No. 406A:轻微损坏修理
6.Repairing Magnesium Parts修理镁零件A.Method No. 406A: Minor Damage RepairMethod No. 406A:轻微损坏修理NOTE: Refer to Method No. 403L for repair of paint coatings for magnesium par...
SECTION IV – REPAIR 9-零件重新喷涂-零件搪瓷漆修复和环氧漆修复
A.Method No. 409A: Enamel Paint Repair of PartsMethod No. 409A:零件搪瓷漆修复Repair painted surfaces of parts as follows:按以下步骤修复零件涂漆表面：(1) Prepare surfaces to be pain...
SECTION III – INSPECTION 1. Standard Inspection Practices -G. 目视检查
G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...
清洁 二 CLEANING
4. Abrasive Cleaning Procedures 磨料清洗程序 A. Deleted. 已删除。 B. Task 1: Dry Abrasive Blast 任务1：干式磨料喷砂 CAUTION: DO NOT USE DRY ABRASIVE BLAST ON SURFACES WITH 63 RA OR...
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...
SECTION III – INSPECTION 1. Standard Inspection Practices -K.过滤器气泡点检查
K.Bubble Point Check for Filters过滤器气泡点检查(1) Perform bubble point test on filter in accordance with MIL-F-5504B.根据MIL-F-5504B对过滤器进行气泡点测试。(a) The largest pore s...
SECTION VI – PACKAGING – 包装（完）
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
SECTION IV – REPAIR 6 -修理镁零件-B.Method No. 406B:镁合金零件严重损坏修复
6.Repairing Magnesium Parts修理镁零件B.Method No. 406B: Magnesium-Alloy Parts Heavy Damage RepairMethod No. 406B:镁合金零件严重损坏修复Repair minor damage to magnesium-alloy parts ...
6740F010000,6740G010000 OVERPRESSURE VALVE
一、名称OVERPRESSURE VALVE超压活门二、件号6740F010000,6740G010000三、章节号36-11-12四、适用机型A320五、系统36 PNEUMATIC气源六、安装位置发动机短舱七、部件原理Operation Fig FUNC-3工...
