张群
SECTION IV – REPAIR 16-管路与软管修理
16.Repairing Tubing and Flexible Hoses管路与软管修理A.Method No. 416A: Repair Silicone Rubber Insulation on Flexible Hose AssembliesMethod No.416A：软管组件硅橡胶绝缘层修理This pro...
SECTION IV – REPAIR 6 -修理镁零件-B.Method No. 406B:镁合金零件严重损坏修复
6.Repairing Magnesium Parts修理镁零件B.Method No. 406B: Magnesium-Alloy Parts Heavy Damage RepairMethod No. 406B:镁合金零件严重损坏修复Repair minor damage to magnesium-alloy parts ...
INSPECTION 检查 三 Inspection Procedures
一份全面的航空部件无损检测（NDT）程序手册，详述了14项检测方法。涵盖射线检测（ASTM E1742）、超声波检测（MIL-STD-2154）、敲击测试、接触式蓝染、表面淬火层检测（MIL-STD-867）、硝酸盐蚀...
HOEYWELL SECTION II – CLEANING 2. 清洁溶液的配制
2. Preparation of Cleaning Solutions 清洁溶液的配制WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATI...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-O. Method No. 403O:镁的化学膜修补
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用O.Method No. 403O: Chemical Film Touch-Up of MagnesiumMethod No. 403O:镁的化学膜修补(1) Remov...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-F.Method No. 407F: 松动、磨损或损坏的销钉（钢制零件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407F: Loose, Worn, or Damaged Pins (Steel Parts) ReplacementMethod No. 40...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-H.Method No. 407H：松动、磨损或损坏的 Rosan螺柱和钢丝螺套的更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板H.Method No. 407H: Loose, Worn, or Damaged Rosan Stud and Insert ReplacementMethod No....
HOEYWELL SECTION II – CLEANING 1. 标准清洁程序-通用
TABLE OF CONTENTS 目录SECTION 章节1. Standard Cleaning Practices标准清洁规范A. General通用2. Preparation of Cleaning Solutions清洁溶液的配制A. Method No. 202A: Alkaline Cleaning So...
第一章 安全操作常识
安全操作常识第一节 安全施工 做任何带高压有危险的电气/电子系统工作比如：——由带电导线接触而产生的电击；——由掉下的工具横在电气导线或导体之间造成的短路；——在现存易燃气体中产生电...
INSPECTION 检查 三 Inspection Procedures
2. Inspection Procedures 检查程序 A. Refer to Quality Work Instruction QWI 205-C-003, which replaces MIL-STD-105.参照质量工作指令QWI 205-C-003（替代MIL-STD-105标准）。 B. Task 1: F...
SECTION III – INSPECTION 1. Standard Inspection Practices -I.弧形联轴器检查
I.Curvic Coupling Inspection 弧形联轴器检查NOTE: Nomenclature for curvic coupling is provided in Figure 320.注：图 320 中提供了弧形联轴器的命名。(1) Inspect components with curvic ...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-D.Method No. 407D:更换松动、磨损和/或损坏的衬套（钢制零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-G.Method No. 407G:松动、磨损或损坏的销钉（铝或镁零件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板G.Method No. 407G: Loose, Worn, or Damaged Pins (Aluminum or Magnesium Parts) Replacem...
第三章 标准线路施工手册（SWPM）介绍
本文介绍标准线路施工手册（SWPM）的基本功能与使用方法，包括通过线号或系统章节查找导线、导线束的方法，以及线型代码（WTC）的查询步骤，帮助维修人员高效查阅手册。
