张群
SECTION III – INSPECTION 1. Standard Inspection Practices -E. 轴承检查
E. Bearing Inspection轴承检查(1) Separable Bearings:可分解的轴承。Table 301. Separable Bearing Defect Definitions表301 可分解轴承缺陷的定义Term项目Definition (Description of Defect...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-N.Method No. 403N: 铝的化学膜修补
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用N.Method No. 403N: Chemical Film Touch-Up of AluminumMethod No. 403N: 铝的化学膜修补(1) Remov...
737NG-ATA 56 窗户【系统原理】
WINDOWS目录1．介绍2．驾驶舱风挡介绍3．驾驶舱固定风挡1）1＃风挡 2）3＃风挡 3）4＃、5＃风挡 4．驾驶舱活动风挡1）2＃活动风挡5．客舱窗户一般描述6．应急出口窗户一般描述7．机舱门观...
HOEYWELL SECTION II – CLEANING 3. Standard Cleaning Methods 标准清洁方法
3. Standard Cleaning Methods 标准清洁方法 CAUTION: SPECIFIED CLEANING METHODS OUTLINED MUST BE FOLLOWED. THE VARIOUS SOLUTIONS AND MATERIALS SPECIFIED IN THE CLEANING METHODS CAN B...
SECTION IV – REPAIR 8-齿轮齿修复-A.Method No. 408A:齿轮齿渐开线表面轻微损伤修复
8. Repairing Gear Teeth齿轮齿修复A.Method No. 408A: Minor Gear Teeth Involute Surface Damage RepairMethod No. 408A:齿轮齿渐开线表面轻微损伤修复Repair minor surface damage on gear t...
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-E.Method No. 407E: 松动、磨损或损坏的衬套（铝或镁部件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407E: Loose, Worn, or Damaged Bushings (Aluminum or Magnesium Parts) Repl...
SECTION IV – REPAIR 5.清除钢制零件上的损伤-C.Method No. 405C: 使用玻璃珠喷丸修复密封直径（唇形密封面）
5.Removing Damage from Steel Parts清除钢制零件上的损伤C.Method No. 405C: Seal Diameter (Lip Seal Surface) Repair Using Glass Bead PeeningMethod No. 405C: 使用玻璃珠喷丸修复密封直径...
SECTION IV – REPAIR 3.防护涂料及电镀的修复与应用-J.Method No. 403J: 选择性电镀
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-D.Method No.403D：金属喷涂修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用D.Method No. 403D: Metal Spray RepairMethod No.403D：金属喷涂修复NOTE: Electric Arc Spray and...
SECTION IV – REPAIR 5.清除钢制零件上的损伤-A.Method No. 405A:微小表面缺陷修复
5.Removing Damage from Steel Parts清除钢制零件上的损伤A.Method No. 405A: Minor Surface Defect RepairMethod No. 405A:微小表面缺陷修复Repair minor surface defects on steel parts as f...
SECTION III – INSPECTION 1. Standard Inspection Practices -O.设备和材料
O.Equipment and Materials设备和材料Table 309 lists equipment and materials that may be required for inspection. Equivalent equipment and materials may be substituted for them.表309...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-C.Method No. 407C:松动或损坏的Keensert螺柱修复
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板C.Method No. 407C: Loose or Damaged Keensert Stud RepairMethod No. 407C:松动或损坏的Ke...
How to Use Torque Wrench (Standard Practices)
How to Use Torque Wrench (Standard Practices)A torque wrench is a specialized tool designed to apply a specific amount of force to a fastener, such as a nut or bolt. This tool is...
SECTION IV – REPAIR 4. 修理铝制零件-D.Method No. 404D:燃油和滑油泵铝制壳体表面修复
4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
