标准 第2页
分类
子分类
排序
SECTION III – INSPECTION 1. Standard Inspection Practices 标准检查施工
SECTION III – INSPECTION第三章 – 检查TABLE OF CONTENTS目录SECTION章节1. Standard Inspection Practices标准检查施工A. General通用B. General Inspection Procedures通用检查程序C. Magn...
6月14日
SECTION VI – PACKAGING – 包装（完）
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
11月22日
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
11月22日
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
11月22日
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
11月22日
SECTION IV – ASSEMBLY 4-压装过盈配合零件
4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...
11月22日
SECTION IV – ASSEMBLY 3-锥形密封件
3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...
11月22日
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
11月22日
SECTION IV – ASSEMBLY 1-通用组装程序
1. General Assembly Practices 通用组装程序A. Protecting Unit During Assembly组装过程中的部件防护Maintain fits and clearances as specified in applicable manual for unit in work. Exe...
11月21日
SECTION IV – REPAIR 17-密封件修理（硅橡胶）
17. Repairing Seals (Silicone Rubber) 密封件（硅橡胶）修理 A. Method No. 417A: Repair of Disbonded Seals (Silicone Rubber)Method No.417A：脱胶密封件修理（硅橡胶） (1) Remove damage...
11月20日
SECTION IV – REPAIR 16-管路与软管修理
16.Repairing Tubing and Flexible Hoses管路与软管修理A.Method No. 416A: Repair Silicone Rubber Insulation on Flexible Hose AssembliesMethod No.416A：软管组件硅橡胶绝缘层修理This pro...
11月20日
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
11月17日
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
11月15日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-E.Method No. 407E: 松动、磨损或损坏的衬套（铝或镁部件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407E: Loose, Worn, or Damaged Bushings (Aluminum or Magnesium Parts) Repl...
11月3日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-D.Method No. 407D:更换松动、磨损和/或损坏的衬套（钢制零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...
11月3日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-F.Method No. 407F: 松动、磨损或损坏的销钉（钢制零件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407F: Loose, Worn, or Damaged Pins (Steel Parts) ReplacementMethod No. 40...
11月3日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-G.Method No. 407G:松动、磨损或损坏的销钉（铝或镁零件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板G.Method No. 407G: Loose, Worn, or Damaged Pins (Aluminum or Magnesium Parts) Replacem...
11月3日
SECTION IV – REPAIR 10. 铆接零件修复
10. Repairing Riveted Parts 铆接零件修复 A. Method No. 410A: Damaged Rivet Replacement General GuidelinesMethod No. 410A:损坏铆钉更换通用准则 (1) Replace damage rivets as follows: ...
11月7日
SECTION IV – REPAIR 11-焊接零件修理
Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...
11月7日
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
11月15日
