标准 第5页
分类
子分类
排序
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
11月22日
HOEYWELL INTRODUCTION 介绍
INTRODUCTION介绍 1. General 通用 Information provided in this manual pertains to overhaul and repair processing for parts manufactured by Honeywell Inc., Phoenix, Arizona. 本手册提...
2月13日
Sealing Compounds
Sealing Compounds 密封化合物 Certain areas of all aircraft are sealed to withstand pressurization by air, to prevent leakage of fuel, to prevent passage of fumes, or to prevent cor...
7月17日
SOPM20-30-84耐溶剂有机涂料的一般清洗用溶剂（84系列）
喷涂前金属最终清洗的溶剂（84系列）SOLVENTS FOR FINAL CLEANING OF METAL BEFORE PAINTING (SERIES 84) 1. GENERAL 通用 A. This subject contains a list of solvents for final cl...
3月10日
SOPM20-30-93燃油箱密封前的最终清洗用溶剂（93系列）
燃油箱密封前的最终清洗用溶剂（93系列）SOLVENTS FOR FINAL CLEANING BEFORE FUEL TANK SEALING (SERIES 93) 1. GENERAL 通用 A. This subject contains a listof solvents for final cleanin...
3月13日
SOPM20-30-86喷涂前抗溶剂有机涂层最终清洗的溶剂（86系列）
喷涂前抗溶剂有机涂层最终清洗的溶剂（86系列）SOLVENTS FOR FINAL CLEANING OF SOLVENT RESISTANT ORGANIC COATINGS BEFORE PAINTING (SERIES 86) 1. GENERAL 通用 A. This subject contai...
3月10日
SOPM20-43-04电刷电镀、阳极氧化和电化学蚀刻
电刷电镀、阳极氧化和电化学蚀刻BRUSH PLATING, ANODIZING AND ELECTROCHEMICAL ETCHING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC 5...
3月18日
SECTION IV – REPAIR 11-焊接零件修理
Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...
11月7日
SECTION IV – REPAIR 12-动平衡操作规程与指南
12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...
11月12日
SECTION IV – ASSEMBLY 8-Marman卡箍（联轴器）安装
8.Marman Clamp (Coupling) InstallationMarman卡箍（联轴器）安装(1) Position clamp over mating component flanges as described in applicable manual.参照适用手册说明，将卡箍定位于配合...
11月22日
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-J.Method No. 407J: 松动、磨损或损坏的螺母板（焊接式）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板 J.Method No. 407J: Loose, Worn or Damaged Nutplate (Welded) ReplacementMethod No. 40...
11月3日
SOPM20-50-17液压组件的防腐蚀处理程序
液压组件的防腐蚀处理程序CORROSION PROTECTION PROCEDURES FOR HYDRAULIC COMPONENTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification Control Dr...
3月30日
SOPM20-50-02安装安全装置（保险）
安装安全装置（保险）INSTALLATION OF SAFETYING DEVICES 1. INTRODUCTION 介绍 A. The information in this subject comes from Boeing Process Specification BAC5018 for installation of...
3月21日
SOPM20-44-01专用涂料和饰面的应用
专用涂料和饰面的应用APPLICATION OF SPECIAL PURPOSE COATINGS AND FINISHES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specifications BAC5710 and BAC58...
3月20日
SOPM20-42-06电镀银
电镀银SILVER PLATING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5715. The airline has a copy of the Boeing Process Specification...
3月15日
SOPM20-50-04在钻孔中安装固定销和塞子
在钻孔中安装固定销和塞子INSTALLATION OF PERMANENT PINS AND PLUGS IN DRILL PASSAGES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5061 ...
3月21日
SECTION IV – REPAIR 6 -修理镁零件-A.Method No. 406A:轻微损坏修理
6.Repairing Magnesium Parts修理镁零件A.Method No. 406A: Minor Damage RepairMethod No. 406A:轻微损坏修理NOTE: Refer to Method No. 403L for repair of paint coatings for magnesium par...
10月8日SOPM20-43-01铬酸阳极化
铬酸阳极化CHROMIC ACID ANODIZING 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5019. The airline has a copy of the Boeing Process S...
3月17日
SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...
7月25日
