3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...

12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...

CAUTION: DO NOT USE THE MECHANICAL STANDARD PRACTICES MANUAL BY ITSELF. USE IT ONLY AS SPECIFIED IN THE APPLICABLE COMPONENT MAINTENANCE MANUAL OR OTHER FAA-APPROVED DOCUMENTS...

结构粘接前的最终清洗用溶剂（97系列）SOLVENTS FOR FINAL CLEANING BEFORE STRUCTURAL BONDING (SERIES 97)   1. GENERAL 通用 A. Thissubject contains a list of solvents for final clea...

  喷涂前复合材料最终清洗的溶剂（87系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE PAINTING (SERIES 87)   1. GENERAL 通用 A. This subject contains a list of solvents for...

非结构粘接前复合材料最终清洗的溶剂（91系列）SOLVENTS FOR FINAL CLEANING OF COMPOSITES BEFORE NON-STRUCTURAL BONDING (SERIES 91) 1. GENERAL 通用 A. This subject contains a list of...

4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...

如何制作和安装树脂粘合层叠垫片和固体填充物HOW TO MAKE AND INSTALL RESIN BOND LAMINATED SHIMS AND SOLID FILLERS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Pr...

在钻孔中安装固定销和塞子INSTALLATION OF PERMANENT PINS AND PLUGS IN DRILL PASSAGES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5061 ...

  非结构粘接前金属最终清洗的溶剂（88系列）SOLVENTS FOR FINAL CLEANING OF METAL BEFORE NON-STRUCTURAL BONDING (SERIES 88) 1. GENERAL 通用 A. This subject contains a list of solve...

  耐化学和耐溶剂饰面的应用APPLICATION OF CHEMICAL AND SOLVENT RESISTANT FINISHES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5736 a...

Sealing Compounds 密封化合物 Certain areas of all aircraft are sealed to withstand pressurization by air, to prevent leakage of fuel, to prevent passage of fumes, or to prevent cor...

Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...

5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...

  复合材料一般清洗用溶剂（83系列）SOLVENTS FOR GENERAL CLEANING OF COMPOSITES (SERIES 83)   1. GENERAL 通用 A. This subject contains a list of solvents for general cleaning of c...

电镀银SILVER PLATING   1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5715. The airline has a copy of the Boeing Process Specification...

Switches 开关Switches control the current flow in most aircraft electrical circuits. A switch is used to start, to stop, or to change the direction of the current flow in the circu...

Seals 密封 Seals are used to prevent fluid from passing a certain point, as well as to keep air and dirt out of the system in which they are used. The increased use of hydraulics a...