分类
子分类
排序
SOPM20-11-07表面安装设备的拆除和更换
表面安装设备的拆除和更换REMOVAL AND REPLACEMENT OF SURFACE MOUNTED DEVICES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5128 (which s...
2025-03-05
SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
2025-09-02
SECTION IV – REPAIR 12-动平衡操作规程与指南
12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...
2025-11-12
第一章 安全操作常识
安全操作常识第一节 安全施工 做任何带高压有危险的电气/电子系统工作比如：——由带电导线接触而产生的电击；——由掉下的工具横在电气导线或导体之间造成的短路；——在现存易燃气体中产生电...
2026-06-17
SECTION IV – REPAIR 4. 修理铝制零件-E.Method No. 404E:轻微腐蚀修复
4. Repairing Aluminum Parts 修理铝制零件E.Method No. 404E: Minor Corrosion RepairMethod No. 404E:轻微腐蚀修复Remove minor corrosion from aluminum-alloy parts as follows:按如下步骤...
2025-10-01
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-K.Method No. 403K:修复受损的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用K.Method No. 403K: Repair of Damaged Paint Coatings - Epoxy-Amine SystemsMethod No. 403K:修复...
2025-09-15
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
2025-11-22
SOPM20-10-07钛的机械加工
钛的机械加工MACHINING OF TITANIUM 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5492, and Boeing Operators Handbook 6M59-553, 'Machini...
2025-02-21
SECTION III – INSPECTION 1. Standard Inspection Practices -F. 齿轮和花键检查
F. Gear and Spline Inspection 齿轮和花键检查(1) Check gear and spline teeth as follows:检查齿轮和花键齿，如下所示：(a) Perform visual check using a strong light and a minimum of 5 ...
2025-07-15
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-E.Method No. 407E: 松动、磨损或损坏的衬套（铝或镁部件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407E: Loose, Worn, or Damaged Bushings (Aluminum or Magnesium Parts) Repl...
2025-11-03
CONSUMABLE MATERIALS消耗性材料
2025-11-30
SOPM20-50-22如何安装钢丝螺套
如何安装钢丝螺套HOW TO INSTALL THREADED INSERTS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Standard BAC5064. The airline has a copy of the Boeing Pr...
2025-03-31
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-A.Method No. 403A: 阳极氧化铝和铝合金修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用A.Method No. 403A: Anodized Aluminum and Aluminum-alloy RepairMethod No. 403A: 阳极氧化铝和铝...
2025-09-11
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
2025-11-15
SECTION IV – REPAIR 5.清除钢制零件上的损伤-A.Method No. 405A:微小表面缺陷修复
5.Removing Damage from Steel Parts清除钢制零件上的损伤A.Method No. 405A: Minor Surface Defect RepairMethod No. 405A:微小表面缺陷修复Repair minor surface defects on steel parts as f...
2025-10-01
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-L.Method No. 403L: 修复因底漆和面漆损坏而暴露裸露镁的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用L.Method No. 403L: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
2025-09-15
