分类
子分类
排序
SOPM20-60-04杂项材料
杂项材料MISCELLANEOUS MATERIALS 1. INTRODUCTION 介绍 A. Materials identified in the overhaul instructions but not in the lists in other SOPM subjects are in this list. 大修说明中列...
2025-04-01
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-B.Method No. 403B: 硬铬镀件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用B.Method No. 403B: Hard Chrome Plated Parts RepairMethod No. 403B: 硬铬镀件修复NOTE: Hard chr...
2025-09-12
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
2025-11-15
SECTION IV – REPAIR 5.清除钢制零件上的损伤-B.Method No. 405B:去除严重腐蚀、硬碳、油漆和氧化皮
5.Removing Damage from Steel Parts清除钢制零件上的损伤B.Method No. 405B: Heavy Corrosion, Hard Carbon, Paint, and Scale RemovalMethod No. 405B:去除严重腐蚀、硬碳、油漆和氧化皮Remov...
2025-10-01
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-M.Method No. 403M:修复因底漆和面漆损坏而暴露裸露铝的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用M.Method No. 403M: Repair of Paint Coatings Damaged Through Primer and Paint Topcoat, Exposin...
2025-09-15
SECTION IV – ASSEMBLY 8-Marman卡箍（联轴器）安装
8.Marman Clamp (Coupling) InstallationMarman卡箍（联轴器）安装(1) Position clamp over mating component flanges as described in applicable manual.参照适用手册说明，将卡箍定位于配合...
2025-11-22
SOPM20-10-27激光沉积钛
激光沉积钛LASER DEPOSITED TITANIUM 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Material Specification BMS 7-361 for laser deposition of titanium. Access t...
2025-02-22
SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...
2025-07-25
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-G.Method No. 407G:松动、磨损或损坏的销钉（铝或镁零件）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板G.Method No. 407G: Loose, Worn, or Damaged Pins (Aluminum or Magnesium Parts) Replacem...
2025-11-03
清洁 二 CLEANING
4. Abrasive Cleaning Procedures 磨料清洗程序 A. Deleted. 已删除。 B. Task 1: Dry Abrasive Blast 任务1：干式磨料喷砂 CAUTION: DO NOT USE DRY ABRASIVE BLAST ON SURFACES WITH 63 RA OR...
2026-01-19
SOPM20-70-01飞机部件的保护、储存和处理
飞机部件的保护、储存和处理PROTECTION, STORAGE AND HANDLING OF AIRPLANE COMPONENTS1. INTRODUCTION 介绍A. The data in this subject comes from Boeing Process Specifications BAC5401, B...
2025-04-01
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-C.Method No.403C：薄而致密的镀铬零件修复
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用C.Method No. 403C: Thin Dense Chrome Plated Parts RepairMethod No.403C：薄而致密的镀铬零件修...
2025-09-13
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
2025-11-17
第三章 标准线路施工手册（SWPM）介绍
本文介绍标准线路施工手册（SWPM）的基本功能与使用方法，包括通过线号或系统章节查找导线、导线束的方法，以及线型代码（WTC）的查询步骤，帮助维修人员高效查阅手册。
2026-06-21
SOPM20-00-00 介绍
介绍INTRODUCTION The instructions in this manual tell how to do standard shop procedures during maintenance functions from simple checks and replacement to complete shop-type repai...
2025-01-23
SECTION IV – REPAIR 5.清除钢制零件上的损伤-C.Method No. 405C: 使用玻璃珠喷丸修复密封直径（唇形密封面）
5.Removing Damage from Steel Parts清除钢制零件上的损伤C.Method No. 405C: Seal Diameter (Lip Seal Surface) Repair Using Glass Bead PeeningMethod No. 405C: 使用玻璃珠喷丸修复密封直径...
2025-10-01
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-N.Method No. 403N: 铝的化学膜修补
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用N.Method No. 403N: Chemical Film Touch-Up of AluminumMethod No. 403N: 铝的化学膜修补(1) Remov...
2025-09-22
