分类
子分类
排序
SPM 20-90-01波音氧气系统部件清洁工艺(Cobham)
2025-08-30
SOPM20-11-06缠绕导线电气连接的修理
缠绕导线电气连接的修理REPAIR OF WRAPPED WIRE ELECTRICAL CONNECTIONS 1. INTRODUCTION 介绍 A. A wrapped wire connection consists of a helix of continuous, solid, uninsulated wire ...
2025-03-02
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
2025-09-02
SECTION IV – REPAIR 11-焊接零件修理
Repairing Welded Parts 焊接零件修理 NOTE: Refer to applicable manual for unit for specialized welding. 注：特殊焊接操作请参阅设备适用手册。 A. Method No. 411A: Fusion Weld Repair o...
2025-11-07
如何使用扭矩扳手
How to Use Torque Wrench (Standard Practices)如何使用扭矩扳手（标准操作规范）A torque wrench is a specialized tool designed to apply a specific amount of force to a fastener, suc...
2026-05-20
SECTION IV – REPAIR 4. 修理铝制零件-D.Method No. 404D:燃油和滑油泵铝制壳体表面修复
4. Repairing Aluminum Parts 修理铝制零件D.Method No. 404D: Fuel and Oil Pump Aluminum Housing Surface RepairMethod No. 404D:燃油和滑油泵铝制壳体表面修复Repair worn and/or damaged s...
2025-10-01
SECTION IV – REPAIR 3.防护涂料及电镀的修复与应用-J.Method No. 403J: 选择性电镀
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用J.Method No. 403J: Selective ElectroplatingMethod No. 403J:选择性电镀NOTE: If parts out of ap...
2025-09-15
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
2025-11-22
SOPM20-10-06导电涂层的修理
导电涂层的修理REPAIR OF CONDUCTIVE COATINGS 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5837 for preparation of exterior plastic sur...
2025-02-21
SECTION III – INSPECTION 1. Standard Inspection Practices -E. 轴承检查
E. Bearing Inspection轴承检查(1) Separable Bearings:可分解的轴承。Table 301. Separable Bearing Defect Definitions表301 可分解轴承缺陷的定义Term项目Definition (Description of Defect...
2025-06-30
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-D.Method No. 407D:更换松动、磨损和/或损坏的衬套（钢制零件）
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板D.Method No. 407D: Replace of Loose, Worn, and/or Damaged Bushing (Steel Parts)Method ...
2025-11-03
SOPM20-11-07表面安装设备的拆除和更换
表面安装设备的拆除和更换REMOVAL AND REPLACEMENT OF SURFACE MOUNTED DEVICES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing process specification BAC5128 (which s...
2025-03-05SECTION IV – REPAIR 2.溶液制备
2.Preparation of Solutions溶液制备WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATION, WASH HANDS AN...
2025-09-02
SECTION IV – REPAIR 12-动平衡操作规程与指南
12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...
2025-11-12
第一章 安全操作常识
安全操作常识第一节 安全施工 做任何带高压有危险的电气/电子系统工作比如：——由带电导线接触而产生的电击；——由掉下的工具横在电气导线或导体之间造成的短路；——在现存易燃气体中产生电...
2026-06-17
SECTION IV – REPAIR 4. 修理铝制零件-E.Method No. 404E:轻微腐蚀修复
4. Repairing Aluminum Parts 修理铝制零件E.Method No. 404E: Minor Corrosion RepairMethod No. 404E:轻微腐蚀修复Remove minor corrosion from aluminum-alloy parts as follows:按如下步骤...
2025-10-01
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-K.Method No. 403K:修复受损的油漆涂层-环氧胺体系
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用K.Method No. 403K: Repair of Damaged Paint Coatings - Epoxy-Amine SystemsMethod No. 403K:修复...
2025-09-15
