张群
A330-35 氧气系统
A330-200/300飞机氧气系统完整培训教材（RR Trent 700/ME构型），涵盖飞行机组氧气系统（高压氧气瓶/面罩调节器/存放箱）、旅客氧气系统（化学发生器/气态氧气可选装）、便携式氧气设备（PBE/便...
SOPM20-50-16压接钢索的组装
压接钢索的组装ASSEMBLY OF SWAGED CABLES 1. INTRODUCTION 介绍 A. The data in this subject comes from Boeing Process Specification BAC5002. Access to the Boeing Process Specification...
SECTION III – INSPECTION 1. Standard Inspection Practices -G. 目视检查
G. Visual Inspection目视检查(1) General Information通用信息(a) Visual inspection involves viewing the part for general appearance in an effort to locate conditions, which cause or ...
第六章 拼接头的夹接、导线与电缆的修理
详解航空器拼接头夹接与导线/电缆修理标准施工，涵盖拼接头夹接工具与尺寸要求、电源馈线拼接、普通/高振动/高温区域导线修理、数据电缆（含629总线）及屏蔽层破损的三种修复方法（金属小环、钢...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-I.Method No. 407I:松动、磨损或损坏的螺母板（铆接式）更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板I.Method No. 407I: Loose, Worn or Damaged Nutplate (Riveted) ReplacementMethod No. 407...
第七章 插头（座）的装配及工具的使用
详解航空插头（座）装配标准施工工艺，涵盖手动/气动/液压夹接工具操作、插钉/孔夹接与送退方法（前退/后退）、插头尾部屏蔽地线四种制作方式、插头磅力矩操作及保险丝制作，适用于SWPM手册施工...
SECTION IV – REPAIR 9-零件重新喷涂-零件搪瓷漆修复和环氧漆修复
A.Method No. 409A: Enamel Paint Repair of PartsMethod No. 409A:零件搪瓷漆修复Repair painted surfaces of parts as follows:按以下步骤修复零件涂漆表面：(1) Prepare surfaces to be pain...
6740F010000,6740G010000 OVERPRESSURE VALVE
一、名称OVERPRESSURE VALVE超压活门二、件号6740F010000,6740G010000三、章节号36-11-12四、适用机型A320五、系统36 PNEUMATIC气源六、安装位置发动机短舱七、部件原理Operation Fig FUNC-3工...
SECTION VI – PACKAGING – 包装（完）
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
SECTION IV – REPAIR 6 -修理镁零件-A.Method No. 406A:轻微损坏修理
6.Repairing Magnesium Parts修理镁零件A.Method No. 406A: Minor Damage RepairMethod No. 406A:轻微损坏修理NOTE: Refer to Method No. 403L for repair of paint coatings for magnesium par...
FE256 EMERGENCY DOOR DAMPER ACTUATOR
一、名称EMERGENCY DOOR DAMPER ACTUATOR应急门阻尼作动器二、件号FE256-000,FE256-000 Amdt A,FE256-001,FE256-001 Amdt A三、章节号52-11-07四、适用机型A330五、系统52 DOORS舱门六、安装位...
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
SECTION IV – REPAIR 10. 铆接零件修复
10. Repairing Riveted Parts 铆接零件修复 A. Method No. 410A: Damaged Rivet Replacement General GuidelinesMethod No. 410A:损坏铆钉更换通用准则 (1) Replace damage rivets as follows: ...
SECTION IV – REPAIR 16-管路与软管修理
16.Repairing Tubing and Flexible Hoses管路与软管修理A.Method No. 416A: Repair Silicone Rubber Insulation on Flexible Hose AssembliesMethod No.416A：软管组件硅橡胶绝缘层修理This pro...
SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意：...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-A.Method No. 407A：松动或损坏螺纹钢丝螺套更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板 NOTE: Refer to Method No. 415A, and 415B for repairing damaged/oversized diameters w...
