6730F010000 FAN AIR VALVE
一、名称FAN AIR VALVE风扇活门二、件号6730F010000,6730F010000 Amdt A三、章节号36-11-11四、适用机型A319, A320五、系统36-PNEUMATIC气动六、安装位置发动机吊架七、部件原理A. General Desc...
3399100 HIGH PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLER/HPFAC – high pressure fan air controller
一、名称HIGH PRESSURE REGULATOR AND SHUTOFF VALVE CONTROLLERHPFAC - high pressure fan air controller高压调节器及关断活门控制器HPFAC - 高压风扇控制器(在七、部件原理和九、在飞机系统...
3290476 SURGE CONTROL VALVE
一、名称SURGE CONTROL VALVE防喘控制活门二、件号3290476-3~-5三、章节号49-50-95四、适用机型A330/A340五、系统49 AIRBORNE AUXILIARY POWER机载辅助动力装置(APU)六、安装位置APU， 315区域...
SECTION VI – PACKAGING – 包装（完）
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
SECTION IV – ASSEMBLY 8-Marman卡箍（联轴器）安装
8.Marman Clamp (Coupling) InstallationMarman卡箍（联轴器）安装(1) Position clamp over mating component flanges as described in applicable manual.参照适用手册说明，将卡箍定位于配合...
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
SECTION IV – ASSEMBLY 4-压装过盈配合零件
4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...
SECTION IV – ASSEMBLY 3-锥形密封件
3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
SECTION IV – ASSEMBLY 1-通用组装程序
1. General Assembly Practices 通用组装程序A. Protecting Unit During Assembly组装过程中的部件防护Maintain fits and clearances as specified in applicable manual for unit in work. Exe...
SECTION IV – REPAIR 17-密封件修理（硅橡胶）
17. Repairing Seals (Silicone Rubber) 密封件（硅橡胶）修理 A. Method No. 417A: Repair of Disbonded Seals (Silicone Rubber)Method No.417A：脱胶密封件修理（硅橡胶） (1) Remove damage...
SECTION IV – REPAIR 16-管路与软管修理
16.Repairing Tubing and Flexible Hoses管路与软管修理A.Method No. 416A: Repair Silicone Rubber Insulation on Flexible Hose AssembliesMethod No.416A：软管组件硅橡胶绝缘层修理This pro...
790390 FAN AIR TEMPERATURE SENSOR
一、名称FAN AIR TEMPERATURE SENSOR风扇空气温度传感器二、件号790390-1~-5,S210T120-108,-118三、章节号36-11-13四、适用机型B747/B767五、系统36-PNEUMATIC气动六、安装位置发动机吊架七、部...
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
