分类
子分类
排序
HOEYWELL SECTION II – CLEANING 3. Standard Cleaning Methods 标准清洁方法
3. Standard Cleaning Methods 标准清洁方法 CAUTION: SPECIFIED CLEANING METHODS OUTLINED MUST BE FOLLOWED. THE VARIOUS SOLUTIONS AND MATERIALS SPECIFIED IN THE CLEANING METHODS CAN B...
SECTION IV – REPAIR 9-零件重新喷涂-零件搪瓷漆修复和环氧漆修复
A.Method No. 409A: Enamel Paint Repair of PartsMethod No. 409A:零件搪瓷漆修复Repair painted surfaces of parts as follows:按以下步骤修复零件涂漆表面:(1) Prepare surfaces to be pain...
SECTION VI – PACKAGING – 包装(完)
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
第五章 接线片的夹接与接线柱的安装
详解航空器接线片夹接与接线柱安装标准施工,涵盖绝缘去除、夹接工具使用、热缩/冷缩管防护、接地桩安装及接地电阻测量。提供屏蔽地线四种制作方法,确保线路维护符合适航要求。
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-A.Method No. 407A:松动或损坏螺纹钢丝螺套更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板 NOTE: Refer to Method No. 415A, and 415B for repairing damaged/oversized diameters w...
SECTION IV – REPAIR 10. 铆接零件修复
10. Repairing Riveted Parts 铆接零件修复 A. Method No. 410A: Damaged Rivet Replacement General GuidelinesMethod No. 410A:损坏铆钉更换通用准则 (1) Replace damage rivets as follows: ...
SECTION IV – REPAIR 1.标准修理程序-概述
1.Standard Repair Practices标准修理程序A.General概述The methods and procedures presented are recommended by the manufacturer to facilitate overhaul and repair of a unit. The inform...
SECTION III – INSPECTION 1. Standard Inspection Practices -H. 电气组件检查
H. Electrical Component Inspection 电气组件检查CAUTION: REFER TO APPLICABLE MANUAL PRIOR TO PERFORMING ANY ELECTRICAL CHECKS TO ENSURE THAT CHECKS WILL NOT DAMAGE EQUIPMENT.注意:...
SECTION IV – REPAIR 6 -修理镁零件-A.Method No. 406A:轻微损坏修理
6.Repairing Magnesium Parts修理镁零件A.Method No. 406A: Minor Damage RepairMethod No. 406A:轻微损坏修理NOTE: Refer to Method No. 403L for repair of paint coatings for magnesium par...
SECTION IV – REPAIR 6 -修理镁零件-C.Method No. 406C:镁合金零件的沟槽和划伤修复
6.Repairing Magnesium Parts修理镁零件C.Method No. 406C: Magnesium-Alloy Parts Gouge and Scoring RepairMethod No. 406C:镁合金零件的沟槽和划伤修复Repair minor damage to magnesium-all...
SECTION IV – REPAIR 6 -修理镁零件-B.Method No. 406B:镁合金零件严重损坏修复
6.Repairing Magnesium Parts修理镁零件B.Method No. 406B: Magnesium-Alloy Parts Heavy Damage RepairMethod No. 406B:镁合金零件严重损坏修复Repair minor damage to magnesium-alloy parts ...
SECTION IV – REPAIR 16-管路与软管修理
16.Repairing Tubing and Flexible Hoses管路与软管修理A.Method No. 416A: Repair Silicone Rubber Insulation on Flexible Hose AssembliesMethod No.416A:软管组件硅橡胶绝缘层修理This pro...
SECTION IV – REPAIR 3. 防护涂料及电镀的修复与应用-O. Method No. 403O:镁的化学膜修补
3. Repair and Application of Protective Coatings and Plating 防护涂料及电镀的修复与应用O.Method No. 403O: Chemical Film Touch-Up of MagnesiumMethod No. 403O:镁的化学膜修补(1) Remov...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-F.Method No. 407F: 松动、磨损或损坏的销钉(钢制零件)更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板F.Method No. 407F: Loose, Worn, or Damaged Pins (Steel Parts) ReplacementMethod No. 40...
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
HOEYWELL SECTION II – CLEANING 2. 清洁溶液的配制
2. Preparation of Cleaning Solutions 清洁溶液的配制WARNING: SOLUTIONS USED FOR CLEANING ARE HAZARDOUS. AVOID INHALING FUMES, DUST, OR MIST. AVOID CONTACT WITH SKIN. AFTER PREPARATI...
SECTION IV – REPAIR 7-更换钢丝螺套、螺柱、衬套、销钉和螺母板-H.Method No. 407H:松动、磨损或损坏的 Rosan螺柱和钢丝螺套的更换
7.Replacing Inserts, Studs, Bushings, Pins and Nutplates更换钢丝螺套、螺柱、衬套、销钉和螺母板H.Method No. 407H: Loose, Worn, or Damaged Rosan Stud and Insert ReplacementMethod No....
HOEYWELL SECTION II – CLEANING 1. 标准清洁程序-通用
TABLE OF CONTENTS 目录SECTION 章节1. Standard Cleaning Practices标准清洁规范A. General通用2. Preparation of Cleaning Solutions清洁溶液的配制A. Method No. 202A: Alkaline Cleaning So...





















