3290476 SURGE CONTROL VALVE
一、名称SURGE CONTROL VALVE防喘控制活门二、件号3290476-3~-5三、章节号49-50-95四、适用机型A330/A340五、系统49 AIRBORNE AUXILIARY POWER机载辅助动力装置(APU)六、安装位置APU， 315区域...
SECTION VI – PACKAGING – 包装（完）
SECTION VI - PACKAGING包装 1.General概述Refer to applicable manual for unit in work for general packaging procedures. For APUs, refer to Service Bulletin 49-7997 for Preservation ...
SECTION IV – ASSEMBLY 8-Marman卡箍（联轴器）安装
8.Marman Clamp (Coupling) InstallationMarman卡箍（联轴器）安装(1) Position clamp over mating component flanges as described in applicable manual.参照适用手册说明，将卡箍定位于配合...
SECTION IV – ASSEMBLY 7 -开口销与键形垫圈
7.Cotter Pins and Key Washers开口销与键形垫圈CAUTION: COTTER PINS ARE NOT REUSABLE. INSTALL NEW COTTER PIN AS SPECIFIED IN APPLICABLE MANUAL FOR UNIT IN WORK.注意：开口销不可重复使...
SECTION IV – ASSEMBLY 6 -保险丝安装与技术
6.Lockwire Installation and Techniques保险丝安装与技术A.General概述Appropriate diameter lockwire (specified in Aerospace Standard 567) is installed using the following techniques a...
SECTION IV – ASSEMBLY 5 -扭矩要求
5. Torque Requirements 扭矩要求 Torque requirements for air, oil and fuel system components depend on the type of parts being fastened or tightened. 空气、滑油及燃油系统组件的扭矩...
SECTION IV – ASSEMBLY 4-压装过盈配合零件
4.Pressing Interference Fit Parts压装过盈配合零件CAUTION: DURING ASSEMBLY OF SOME UNITS, CLOSE TOLERANCE FITS REQUIRE THAT A PART WILL EITHER HAVE TO BE COLD SOAKED OR HEATED IN OR...
SECTION IV – ASSEMBLY 3-锥形密封件
3.Conical Seal锥形密封件NOTE: Conical seals are used at specific locations during engine production to preclude leakage. However, conical seals may be used at any flared tubing fit...
SECTION IV – ASSEMBLY 2-密封与密封件
2.Packing and Seals密封与密封件A.Lubricating and Installing Packings密封润滑与安装Refer to Table 501 when selecting the type of packing lubricant and Figure 501 for a graphic rep...
SECTION IV – ASSEMBLY 1-通用组装程序
1. General Assembly Practices 通用组装程序A. Protecting Unit During Assembly组装过程中的部件防护Maintain fits and clearances as specified in applicable manual for unit in work. Exe...
SECTION IV – REPAIR 17-密封件修理（硅橡胶）
17. Repairing Seals (Silicone Rubber) 密封件（硅橡胶）修理 A. Method No. 417A: Repair of Disbonded Seals (Silicone Rubber)Method No.417A：脱胶密封件修理（硅橡胶） (1) Remove damage...
SECTION IV – REPAIR 16-管路与软管修理
16.Repairing Tubing and Flexible Hoses管路与软管修理A.Method No. 416A: Repair Silicone Rubber Insulation on Flexible Hose AssembliesMethod No.416A：软管组件硅橡胶绝缘层修理This pro...
790390 FAN AIR TEMPERATURE SENSOR
一、名称FAN AIR TEMPERATURE SENSOR风扇空气温度传感器二、件号790390-1~-5,S210T120-108,-118三、章节号36-11-13四、适用机型B747/B767五、系统36-PNEUMATIC气动六、安装位置发动机吊架七、部...
SECTION IV – REPAIR 15-修理损坏/超尺寸螺纹
15. Repairing Damaged/Oversize Threads 修理损坏/超尺寸螺纹 NOTE: Refer to Method No. 407A, 407B, and 407C for repair of loose or damaged inserts. Prepare for and install standard H...
SECTION IV – REPAIR 14-零件重新标记
14. Remarking Parts 零件重新标记Before to start cleaning, locate the marks that can be removed by the cleaning and repainting process. Those marks must be identified and recorded. ...
SECTION IV – REPAIR 13-电气元件修理
13.Repairing Electrical Components 电气元件修理 NOTE: The following methods are typical only. Refer to applicable manual for unit in work for specific instructions. 注：以下方法仅...
SECTION IV – REPAIR 12-动平衡操作规程与指南
12. Balancing Procedures and Guidelines 动平衡操作规程与指南 A. Method No. 412A: Turbine Wheel Assembly Balance Check and Re-balanceMethod No.412A：涡轮叶轮组件平衡检测与再平衡 Reb...
